OneStopList

Gods and goddesses

Apollo Series 65 Smoke Detector Manual Guide

Updated November 21, 2026

The Apollo Series 65 smoke detector manual is not a single public document; it is a set of engineering and installation instructions distributed to fire alarm engineers and technicians, not homeowners. The Series 65 is an addressable analogue smoke sensor designed for use with Apollo’s XP95 and Discovery protocol control panels, and the official manual is titled Series 65 Installation Manual (ref. 65000-004) and is available from Apollo Fire Detectors’ website or through your panel manufacturer.

What the Series 65 Actually Is

The Series 65 is a long-running family of fire detectors introduced in the 1980s and still widely installed across the UK, Europe, and Asia. Unlike a standalone battery smoke alarm you buy at a hardware store, the Series 65 is a component of a two-wire fire alarm control panel system. It does not sound its own alarm; it sends a signal back to the panel, which then triggers sounders, strobes, or a monitoring station. The range includes optical (photo-electric), ionisation, and heat detectors, plus a combined optical/heat model. The most common is the optical smoke detector, model 55000-200 (or 55000-201 for the white version).

How the Detector Works

The optical Series 65 uses a pulsed infrared LED inside a labyrinth chamber. When smoke particles enter the chamber, they scatter the light beam onto a photodiode, which increases the measured signal. The detector’s on-board microprocessor converts this analogue value into a digital reading sent to the control panel. The panel decides when to raise an alarm based on its own programmed thresholds. This design makes the Series 65 less prone to false alarms from steam or cooking than ionisation types, but it is slower to respond to fast-flaming fires with small particles. The heat detector (model 55000-300) uses a thermistor to measure temperature rise, and the ionisation model (55000-100) uses a small radioactive source to detect combustion particles – that model is now rarely sold due to disposal regulations.

Why You Probably Don’t Need the Full Manual

If you are a building owner or facilities manager, the manual’s most useful sections are the installation spacing and maintenance tables. The manual specifies maximum spacing of 10 metres between detectors on smooth ceilings, with a maximum distance of 5 metres from a wall. For sloped ceilings, the spacing changes. It also states that detectors should be at least 0.5 metres from any wall or obstruction, and at least 1 metre from air conditioning vents. The manual’s wiring diagrams are for engineers: the Series 65 connects to a two-wire loop with positive and negative lines, and each detector has a rotary address switch (0–63) that must be set uniquely on the loop. If you are not commissioning the system, you will not need those diagrams.

How to Get the Correct Manual

Because the Series 65 works with multiple protocols, the manual you need depends on your panel. Apollo publishes separate documents:

  • XP95/Discovery protocol manual – for panels using Apollo’s own protocol (e.g., Advanced, Kentec, Morley).
  • Conventional version – the Series 65 also exists in a conventional (non-addressable) form, which uses a different manual and wiring.
  • Marine version – for shipboard installations, with different environmental ratings.

Search for “Series 65 Installation Manual PDF” on Apollo’s official site (apollo-fire.com) under the “Support” or “Downloads” section. The panel manufacturer’s manual may also reference the detector’s commissioning values. If you have a specific panel, contact that brand’s technical support; they will send the correct pages.

Common Problems and Troubleshooting

Users searching for the manual often have a fault light or a false alarm. Common issues with Series 65 detectors include:

  • Dust contamination – the optical chamber accumulates dust over years, causing drift. The manual recommends cleaning with a vacuum cleaner and soft brush; never use water or solvents.
  • Address conflict – two detectors set to the same address cause a loop fault. Check the rotary switches.
  • Wrong base – the Series 65 fits only on the Series 65 base (45681-200). Using an XP95 base will not work.
  • Green LED flashing – this means the detector is in normal operation; a red LED flash indicates a fire alarm condition.

If the detector is over 10 years old, the manual and most national standards (e.g., BS 5839 in the UK) recommend replacement, not repair, because the sensing element degrades.

How to Choose the Right Series 65 Model

Selecting the correct detector is a matter of fire type and environment. The manual’s selection guide is brief but practical:

  • Use optical for slow-burning, smouldering fires (upholstery, paper, wiring) – most common in offices and corridors.
  • Use heat for kitchens, boiler rooms, and dusty areas where smoke detectors would false alarm.
  • Use ionisation for fast-flaming fires (liquids, gases) – but check local regulations on radioactive disposal.
  • Use the optical/heat combined (55000-400) where you need both smoke detection and a fixed temperature alarm in one unit.

Each model has a different part number printed on the back. The manual includes a cross-reference table to confirm which base and which protocol version you have.

Cost and Replacement Parts

The Series 65 is an older product but still in production as of the 2020s. A new optical detector typically costs between £15 and £30 (or $20–$40) from fire safety suppliers, depending on quantity and protocol version. The base costs £5–£10. The manual is free as a PDF. If you are replacing a faulty unit, you can swap the head without rewiring: twist the detector head counter-clockwise to remove it from the base, then fit the new head and set the same address. Do not mix Series 65 heads with XP95 heads on the same loop – the protocols are incompatible, although they look similar.

Safety and Compliance Notes

Working on a fire alarm system is regulated in most countries. In the UK, BS 5839 Part 1 covers system design and installation; Part 6 covers domestic premises. The Series 65 is not intended for ordinary homes – it is a commercial/industrial device. Only a competent person should install or modify it, because incorrect wiring can disable the entire loop. The manual includes a warning that detectors must be tested after installation using a magnet or test smoke, and that the loop must be isolated from the panel before removing a detector. Also note that the ionisation model contains a small americium-241 source; it must not be disposed of in normal waste – return it to a licensed handler.

Frequently Asked Questions

Can I use a Series 65 detector with a conventional (non-addressable) panel? No, unless you buy the conventional version (part numbers starting 55000-500 series). The addressable version communicates digitally and will not work on a simple zone panel.

How do I reset the detector after an alarm? You do not reset the detector itself. Press the reset button on the control panel to clear the alarm condition. The detector will automatically resume normal operation.

Why is my Series 65 LED flashing red every few seconds? A steady red flash in normal standby is the panel polling the detector. If the red LED stays lit, the detector is in alarm. If it flashes rapidly, it may be in a fault condition – check the panel’s display for the specific error.

What is the difference between Series 65 and XP95? XP95 is Apollo’s newer protocol with more advanced features (e.g., drift compensation and faster polling). Series 65 is the older protocol. They are not interchangeable on the same loop, though both use the same physical mounting and base.

How often should I test the detector? The manual and BS 5839 recommend a functional test at least once a year, and a visual inspection every six months. Cleaning the optical chamber should be done as part of the annual service.

Is the Series 65 obsolete? No, it is still supported and sold, but Apollo is phasing it out in favour of the XP95 and Discovery ranges in new installations. Spare parts and manuals remain available.

Related

How pages are sourced and corrected: Sources and editorial policy.