OneStopList

Gods and goddesses

Apollo 65 Smoke Detector Wiring Diagram Guide

Updated November 21, 2026

There is no single official “Apollo 65 smoke detector wiring diagram” because the Apollo 65 is a series of addressable fire alarm detectors and bases, not one fixed device; wiring depends on the specific base model (e.g., XP95, Discovery, or S65) and the control panel. In nearly all cases, the Apollo 65 series uses a two-wire loop connection (positive and negative) for both power and data communication, with the detector base acting as the interface between the loop and the detector head. Below is a practical guide to the standard wiring conventions, base terminals, and common installation scenarios for the Apollo 65 range.

Background: What the Apollo 65 Series Is

The Apollo 65 series refers to a family of addressable smoke and heat detectors introduced by Apollo Fire Detectors, a UK-based manufacturer. The “65” typically indicates the detector’s diameter in millimeters, which is the standard footprint for many European fire alarm devices. This series includes optical smoke detectors, heat detectors, and combined units, all designed to work with Apollo’s XP95, Discovery, and S65 protocol control panels. The detectors themselves do not have fixed wiring; they plug into a separate base (often a series 65 base) that is wired to the loop. The base is the component with screw terminals, and the detector head simply twists or locks onto it.

How the Wiring Works: Loop Topology

Apollo 65 detectors are almost always installed on a two-wire loop, also called a signaling line circuit (SLC). The loop starts at the fire alarm control panel, goes out to each device, and returns to the panel. This allows the panel to power each detector and send/receive digital data on the same two wires. The two wires are typically labeled as positive (L1, +, or A) and negative (L2, –, or B). Polarity must be observed when connecting to the base terminals. The loop is not polarity-sensitive at the detector head itself, but the base terminals are marked, and reversing the loop wires on the base will prevent communication.

Standard Base Terminals and Connections

Apollo 65 bases (such as the 45681-200 series base) have four terminals, usually numbered 1, 2, 3, and 4. Terminals 1 and 2 are for the incoming loop positive and negative, and terminals 3 and 4 are for the outgoing loop to the next device. In practice, you connect the positive loop wire to terminal 1 and the negative loop wire to terminal 2, then run the next segment from terminal 3 (positive out) and terminal 4 (negative out). Some bases also have a remote indicator terminal (often marked R or REM) for connecting an external LED, but this is optional. Always check the specific base datasheet because some variants have a resistor or diode fitted for end-of-line monitoring, which changes the terminal function.

Step-by-Step Wiring Procedure

  • Turn off power to the loop at the control panel and verify zero voltage with a meter before touching any terminals.
  • Strip about 6–8 mm of insulation from each loop wire end.
  • Connect the incoming positive wire to base terminal 1 and the incoming negative wire to terminal 2.
  • Connect the outgoing positive wire to terminal 3 and the outgoing negative wire to terminal 4, continuing to the next device.
  • If using a remote indicator, connect its positive lead to the REM terminal and its negative lead to terminal 2 (or the common negative).
  • Snap the detector head onto the base and rotate clockwise until it locks.
  • Power up the loop and test the detector using the panel’s addressing or test function.

Choosing the Right Base and Detector

Not all Apollo 65 detectors fit all bases. The series 65 base is physically compatible with the XP95 and Discovery detector heads, but the communication protocol differs. An XP95 detector on a Discovery base will not work, and vice versa. When wiring, you must match the detector protocol to the control panel’s protocol. For example, an Apollo 65 optical smoke detector with an XP95 protocol requires an XP95-compatible base and an XP95 panel. The physical wiring is identical, but the data format is not. Always check the detector head label for the protocol (e.g., “XP95” or “Discovery”) before installing.

Common Wiring Problems and Misconceptions

A frequent mistake is assuming the loop is polarity-free at the base. While the detector head itself may be polarity-insensitive, the base terminals are not, and reversing the loop on one base will break communication for all downstream devices. Another common issue is using the wrong end-of-line resistor or diode. In a conventional (non-addressable) system, a resistor is placed across the last detector, but in an addressable Apollo 65 loop, there is no end-of-line resistor; the loop simply returns to the panel. If you see a resistor in the base, it is likely for a remote indicator or a specific panel requirement. Also, many installers mistakenly ground the shield of the loop cable; the shield should be connected to earth at the panel only, not at each base.

Costs and Replacement Considerations

Apollo 65 detectors and bases are mid-range in price, typically costing more than conventional detectors but less than high-end addressable models. A new detector head may cost between $15 and $40 depending on the sensor type (optical, heat, or multi-criteria), and a base costs roughly $5 to $15. When replacing an old detector, you can often reuse the existing base if it is the same protocol and in good condition, but you must match the new head’s protocol to the panel. Mixing protocols on the same loop will cause the panel to report a device fault or fail to recognize the detector. If you are unsure which protocol your system uses, check the panel model or the existing detector head label.

Safety and Code Compliance

Fire alarm wiring must comply with local codes, such as NFPA 72 in the United States or BS 5839 in the United Kingdom. In practice, this means using fire-resistant cable (e.g., FP200 or equivalent), maintaining correct separation from mains power cables, and ensuring all connections are secure and strain-relieved. The loop must be supervised so that an open circuit or short circuit is detected by the panel. Apollo 65 bases are not intrinsically safe; they are designed for standard indoor use. Do not install them in hazardous areas unless using an approved barrier or an intrinsically safe version. Always test the detector after wiring with a smoke test or a magnet to confirm the LED lights and the panel reports the correct address.

Frequently Asked Questions

Can I wire an Apollo 65 detector directly to a conventional panel?

No. The Apollo 65 is an addressable detector that communicates digitally with an addressable control panel. Connecting it directly to a conventional panel will not work because the panel supplies a simple voltage and expects a resistance change, not digital data. You would need an addressable panel or an interface module.

What is the difference between the S65, XP95, and Discovery bases?

The physical base is often the same size and terminal layout, but the electronics inside differ. The S65 is an older protocol, XP95 is a later one, and Discovery is the current generation. They are not interchangeable. A Discovery detector will not work on an XP95 base, and an XP95 detector will not work on a Discovery base, even though the wiring is identical.

Why does my detector show a fault after wiring?

Check the loop polarity at that base, ensure the detector head is fully seated and locked, and verify that the protocol matches the panel. Also check that the loop is not shorted or open at the next device. A common cause is a loose wire in terminal 3 or 4 that breaks the loop to downstream devices.

Do I need an end-of-line resistor for an Apollo 65 loop?

No. Addressable loops do not use end-of-line resistors. The loop returns to the panel, and the panel monitors the full circuit. If you see a resistor in a base, it is for a remote indicator or a specific panel option, not for loop termination.

Can I mix Apollo 65 detectors with other brands on the same loop?

No. Apollo 65 detectors use Apollo’s proprietary communication protocol. Other brands use different protocols, so mixing them on the same loop will cause communication errors. You must use all Apollo devices (or Apollo-compatible third-party devices) on an Apollo loop.

Related

How pages are sourced and corrected: Sources and editorial policy.