OneStopList

Gods and goddesses

Apollo s65 Smoke Detector: What It Is & How It Works

Updated November 21, 2026

The Apollo s65 is a widely used optical smoke detector head, part of the Series 65 range, that is designed to plug into a compatible Apollo base and is commonly found in commercial and industrial fire alarm systems across the UK and many other countries. It works by using an internal light source and sensor to detect smoke particles that enter the detection chamber, triggering an alarm when the light scattered by smoke reaches a preset level. This article explains what the s65 is, how it fits into a fire alarm system, how to install and maintain it, and answers common questions about this specific detector model.

Background and Place in the Series 65 Range

The Apollo Series 65 range was introduced in the 1980s and became one of the most popular conventional fire detector families in Europe and beyond. The s65 is the optical (photoelectric) smoke detector head in that range, distinguished by its model code and by the fact that it is a conventional detector, meaning it operates on a simple two-wire loop and does not carry digital addressing. It is designed to be used exclusively with Apollo Series 65 bases, such as the standard 45681-200 base or the relay base. The s65 is not a standalone alarm; it requires a compatible control panel to process its signal and sound the building alarms. Over the years, Apollo has produced several variants, including the s65 with a built-in thermal sensor (the s65 plus), but the base s65 is purely an optical smoke detector.

How the Optical Detection Works

The s65 uses a principle called light scattering, which is the same method used in most photoelectric smoke detectors. Inside the detector head is a small chamber that is open to the surrounding air but shielded from ambient light. The chamber contains an infrared LED and a photodiode positioned at an angle so that light from the LED does not normally reach the photodiode. When smoke particles enter the chamber, they scatter the infrared light, and some of that scattered light hits the photodiode. When the amount of scattered light exceeds a threshold, the detector goes into alarm. This method is especially sensitive to slow, smouldering fires that produce large visible smoke particles, such as those from overheated wiring, upholstery, or paper. It is less sensitive to fast-flaming fires that produce small, invisible combustion particles, which is why many systems also include ionisation or heat detectors in certain areas.

Installation and Base Compatibility

Installing an s65 is straightforward but requires attention to the correct base and wiring. The detector head twists and locks into a Series 65 base, which is fixed to a ceiling or wall. The base has terminals for the positive and negative loop wires, and some bases include a remote indicator output. To fit the head, align the two small guide pins on the base with the slots on the detector, push gently, and twist clockwise until it clicks. To remove it for cleaning or testing, insert a small screwdriver into the release slot and twist counter-clockwise. The s65 must not be used with any other manufacturer’s base, and it is not compatible with Apollo’s later XP95 or Soteria ranges without an adapter, which is not recommended. Wiring polarity matters: the positive and negative terminals on the base must match the loop polarity from the control panel, otherwise the detector will not power up correctly.

Testing and Maintenance

Regular testing is essential to ensure the s65 still responds to smoke. The simplest test is to use a can of approved smoke detector test aerosol, spraying a short burst into the detector’s vents. The detector should go into alarm within a few seconds. Alternatively, a handheld magnet can be used on some models to simulate a fire condition, but the aerosol test is the standard method. The detector should be cleaned periodically, as dust and insects in the chamber can cause false alarms or reduce sensitivity. To clean, remove the head, gently vacuum the outside vents, and use a soft brush to remove debris from the chamber opening. Do not immerse the detector in water or use solvent cleaners. The s65 has a built-in drift compensation feature in many control panels, but the detector itself does not self-calibrate; the panel may adjust its sensitivity over time. Most manufacturers recommend testing every six months and replacing the detector after ten years of service, though that lifespan is a general guideline and not a hard rule.

Common Problems and Troubleshooting

The most frequent issue with the s65 is false alarms, usually caused by dust, steam, or cooking fumes entering the chamber. If an s65 alarms without a fire, check the area for steam from showers or kettles, and clean the detector as described. Another common problem is the detector not seating properly in its base, which can cause intermittent contact and a fault signal at the panel. Always ensure the head is twisted fully into the locked position. A less common but serious issue is a detector that fails to alarm when tested; this can happen if the LED has failed or the chamber is blocked. If a test fails, replace the detector head immediately. Note that the s65 is a conventional detector, so it does not report a specific address to the panel; it only signals a general zone alarm. If you need to know exactly which detector activated, you must use an addressable system, not the s65.

Comparing the s65 to Other Apollo Detectors

Within the Apollo range, the s65 is often confused with the XP95 optical detector (model 55000-200) or the Soteria optical. The XP95 and Soteria are addressable detectors, meaning each device has a unique digital address and can report its exact location to the control panel. The s65 is conventional, so it only reports a zone. In terms of detection principle, all three use the same optical scattering method, but the XP95 and Soteria have more advanced electronics, including built-in drift compensation and a wider range of sensitivity settings. The s65 is generally cheaper and simpler, making it suitable for smaller installations or retrofits where addressable wiring is not available. If you are replacing an existing s65, you must use another s65 head or upgrade the entire loop to a compatible addressable system; you cannot mix conventional and addressable detectors on the same loop.

Safety and Compliance Considerations

When installing or servicing an s65, always isolate the fire alarm loop at the control panel before removing or fitting heads to avoid electric shock or accidental alarms. The s65 is designed to meet various European standards, including EN 54-7 for point smoke detectors, which is the relevant standard for optical smoke detectors in Europe. It is important to check that the detector has the CE mark and that the installation complies with local building regulations and fire codes. The s65 is not suitable for outdoor use, in areas with high humidity, or in environments with corrosive atmospheres. It should not be painted, as paint will block the vents and prevent smoke from entering. Also, do not use the s65 in areas where the temperature regularly exceeds 50°C or falls below -10°C, as the electronics may not function reliably.

Frequently Asked Questions

Can I use an Apollo s65 without a base? No, the s65 is a detector head only and must be plugged into a compatible Series 65 base that provides the electrical connection and mechanical mounting. The base is sold separately.

How do I know if my s65 is faulty? The most reliable way is to test it with smoke aerosol. If it does not alarm within a few seconds, or if it alarms constantly without smoke, it is likely faulty. Also, check the panel for a fault signal, which can indicate a wiring or contact issue.

Is the s65 compatible with my existing fire alarm panel? It depends on your panel. The s65 is a conventional detector, so it works with any conventional fire alarm control panel that supports two-wire loops and provides the correct voltage (typically 9-28V DC). Check your panel’s documentation for compatibility with Apollo Series 65 detectors.

What is the difference between the s65 and the s65 plus? The s65 plus includes an additional heat sensor (a thermistor) that can detect rapid temperature rises, making it a combined optical and heat detector. The standard s65 only detects smoke.

How often should I replace my s65 detectors? While there is no legal universal rule, most manufacturers and fire safety guidance recommend replacing smoke detectors after 10 years from the date of manufacture, as the sensitivity of the optical components can degrade over time. Check the date code on the detector body.

Can I clean my s65 with compressed air? Yes, you can use a gentle blast of compressed air to remove dust from the vents, but do not direct the air directly into the chamber opening at high pressure, as this can push debris further in. Vacuuming is often safer.

Related

How pages are sourced and corrected: Sources and editorial policy.