OneStopList

Gods and goddesses

Apollo Oil Tank Monitor Not Working? Fixes & Guide

Updated November 20, 2026

If your Apollo oil tank monitor is not working, the most common causes are dead batteries, a disconnected sensor wire, or a faulty transmitter—and most issues can be resolved with basic troubleshooting before you call a technician. Start by checking the display unit’s batteries and the sensor wire connection at the tank; these account for the majority of reported failures. Below is a detailed guide covering how the system works, step-by-step fixes, common error codes, and when to replace components.

How an Apollo Oil Tank Monitor Works

Apollo oil tank monitors are part of a wireless system that measures the fuel level in your home heating oil tank and sends the reading to a display unit inside your house. The system typically includes:

  • A sensor that mounts on or inside the tank (often using ultrasonic or float technology).
  • A transmitter that sends the level data wirelessly to the display.
  • A display unit that shows the fuel level in percentages or gallons.

Apollo’s most common models (like the Apollo 100 or Apollo 200) use a float-based sensor that measures the tank’s fill level. The transmitter is battery-powered and sends a signal to the display, which is typically plugged into a wall outlet. Because the system is wireless, interference or low battery in the transmitter can cause the display to show an error or go blank.

Step-by-Step Troubleshooting

Before you call for service, work through these steps in order. Most issues are simple to fix.

  1. Check the display unit’s power. If the display is blank, unplug it for 30 seconds and plug it back in. If it still doesn’t light up, test the outlet with another device.
  2. Replace the batteries in the transmitter. The transmitter is usually mounted on the tank and uses two AA or AAA batteries. Remove the cover, replace the batteries, and wait up to 15 minutes for the display to update.
  3. Inspect the sensor wire. The sensor connects to the transmitter with a thin wire. Look for cuts, fraying, or loose connections. If the wire is damaged, the transmitter may not send a reading.
  4. Check the sensor’s float. If your tank has a float-type sensor, the float can become stuck on the bottom or side of the tank. Gently tap the sensor or use a long stick to move the float if accessible.
  5. Reset the system. On the display unit, hold the reset button (if present) for 5 seconds. Some models require you to press a combination of buttons—check your manual.
  6. Move the display closer. If the display is far from the tank, the wireless signal may be blocked. Temporarily move the display closer to see if the reading appears.

Common Error Messages and What They Mean

Apollo monitors often display error codes or symbols. Here are the most common ones and their typical causes:

  • “LO” or “–“ – This usually means the transmitter is not communicating. Check the batteries and sensor wire.
  • “ERR” or “E1” – Indicates a sensor fault. The sensor may be disconnected or damaged.
  • “FULL” or “EMPTY” – If the reading doesn’t change after a fill, the float may be stuck.
  • Flashing battery icon – The transmitter battery is low and needs replacement.

If you see an error code not listed here, consult your user manual. Apollo’s customer support can also help identify the code based on your model.

Why the Monitor Might Show the Wrong Level

Sometimes the monitor isn’t completely dead but gives inaccurate readings. This can happen for several reasons:

  • Stuck float: If the float gets caught on the tank’s internal baffle or side, it will report a fixed level.
  • Sensor misalignment: The sensor must be positioned vertically. If it’s tilted, the float may not move correctly.
  • Interference: Metal tanks can weaken the wireless signal, especially if the display is far away.
  • Battery voltage drop: As batteries weaken, the transmitter may send intermittent or incorrect signals.

If your monitor consistently under-reports, you can verify the actual level by dipping the tank with a gauge stick (if your tank has a fill pipe) or by noting how many gallons you ordered at the last fill.

Replacing Batteries and Components

Battery replacement is the most common fix. Here’s what you need to know:

  • Transmitter batteries: Use fresh alkaline batteries (not rechargeable) for best performance. Replace them every 12–18 months, even if the monitor seems fine.
  • Display unit battery backup: Some displays have an internal battery for power outages. If your display shows nothing during an outage, that battery may be dead.
  • Sensor replacement: If the sensor itself fails (e.g., the float breaks or the wire is severed), you can order a replacement sensor from Apollo or an HVAC supplier. Match the model number exactly.

When replacing any component, turn off the power to the display and disconnect the transmitter. Always use the correct replacement parts to avoid damaging the system.

When to Call a Professional

If you’ve completed the troubleshooting steps above and the monitor still doesn’t work, it’s time to call an oil heating technician. They can:

  • Test the sensor with a multimeter to confirm it’s sending a signal.
  • Check for wiring issues inside the tank (if the sensor is mounted internally).
  • Replace the transmitter or display if they’re faulty.

Also, if you notice any oil leaks or unusual smells around the tank, do not attempt repairs yourself—contact a professional immediately for safety.

Alternatives to Apollo Monitors

If your Apollo monitor is beyond repair or you’re looking for a more reliable solution, consider these alternatives:

  • Smart oil tank gauges: Wi-Fi-enabled monitors (like the Watchman or SmartOil) send readings to your smartphone and offer alerts for low levels.
  • Simple dipstick gauges: Mechanical gauges that show the level directly on the tank. They’re cheap and never run out of batteries, but you must go outside to read them.
  • Ultrasonic sensors: These attach to the outside of the tank and measure the fuel level without penetrating the tank. They’re often more accurate than float sensors.

When choosing a replacement, check compatibility with your tank type (steel or plastic) and the distance to your display location.

Frequently Asked Questions

Why does my Apollo monitor show “LO” even after I replaced the batteries?
If the transmitter still shows “LO,” the sensor wire may be disconnected or the sensor itself is faulty. Check the wire connections at the transmitter and the sensor. If they look fine, the sensor may need replacement.

How do I reset my Apollo oil tank monitor?
Unplug the display for 30 seconds, then plug it back in. For the transmitter, remove and reinsert the batteries. This often clears temporary glitches. Some models have a reset button on the display—hold it for 5 seconds.

Can I use rechargeable batteries in the transmitter?
Rechargeable batteries have a lower voltage (1.2V vs 1.5V for alkaline) and may cause the transmitter to malfunction or show a low battery warning. Use fresh alkaline batteries for reliable operation.

How often should I replace the batteries in my Apollo monitor?
Most manufacturers recommend replacing the transmitter batteries every 12–18 months. If you notice the display reading intermittently, replace them sooner.

My monitor is reading empty but I just filled the tank. What’s wrong?
This usually means the float is stuck. Gently tap the sensor or use a long stick to move the float. If that doesn’t work, the sensor may be damaged and need replacement.

Will a metal tank affect the wireless signal?
Yes, metal tanks can weaken the signal between the transmitter and display. If the display is far away, try moving it closer or adding a wireless repeater if your model supports it.

Related

How pages are sourced and corrected: Sources and editorial policy.