OneStopList

Gods and goddesses

Apollo Series 65 Smoke Detector Base Explained

Updated November 21, 2026

The Apollo Series 65 smoke detector base is the mounting and wiring platform used with the Series 65 optical smoke sensor head, providing the electrical connection and physical locking mechanism for the detector in a fire alarm system. It is not a standalone detector; it is the fixed socket that receives the plug-in sensing head, and it comes in several configurations to match different wiring styles and system voltages.

What the Base Actually Does

The base performs three jobs in a conventional fire alarm circuit. First, it physically holds the detector head in place using a twist-and-lock bayonet mechanism, so the head cannot fall out or be removed accidentally. Second, it makes the electrical connection between the detector head and the system wiring via terminal screws on the base body. Third, it provides a release tab or lever that lets an installer remove the head for cleaning or replacement without disconnecting the wiring.

In the Series 65 range, the base is a separate product from the sensor head. You cannot buy a “detector” as a single unit; you must select a base and a head that match. The base is typically white plastic, round, about 100 mm in diameter, and is designed to fit a standard 4-inch (100 mm) ceiling junction box or a European 60 mm fixing centres back box.

Available Base Variants

Apollo offers several Series 65 bases, and the correct choice depends on your system’s wiring topology and whether you need an integral short-circuit isolator.

  • Standard base (45681-200): The basic two-wire base for conventional systems. It has terminals for positive and negative supply plus an optional remote indicator connection.
  • Diode base (45681-211): Contains a diode in the positive line, used for polarity-sensitive applications or where a common positive is needed for multiple zones.
  • Relay base (45681-220): Includes a built-in relay that changes state when the detector alarms, allowing the base to switch an external device such as a sounder or a door release.
  • Isolator base (45681-240): Contains a short-circuit isolator that disconnects a faulty section of the loop in an addressable system, preventing a single short from taking down the whole loop. This base is only used with addressable panels, not conventional ones.
  • Remote indicator base (45681-260): Provides a dedicated terminal for connecting a remote LED indicator, so the alarm state can be seen from a distance.

All bases accept the same Series 65 optical head (58000-200) and the same ionisation head (58000-100) where those are still in service, though ionisation heads are being phased out in many regions due to radioactive source disposal concerns.

How the Wiring Works

Conventional Series 65 bases use a simple two-wire loop. The positive and negative supply wires from the fire alarm control panel are connected to the base terminals. The detector head plugs into the base, and when the head alarms, it draws extra current across the loop, which the panel detects as an alarm condition.

Terminal markings on the base are usually labelled + and –, and some bases have a third terminal for the remote indicator. For the relay base, there are additional terminals for the relay contacts (normally open and common). The isolator base is wired into an addressable loop, not a conventional zone, and it sits between the previous device and the next one in the loop.

A common mistake is to wire a conventional base into an addressable loop or vice versa. The Series 65 conventional bases do not have a communication chip; they are purely passive. Addressable systems require the XP95 or Discovery range bases, which are electrically different. If you fit a Series 65 conventional head onto an addressable base, it will not communicate with the panel.

Choosing the Right Base

Before you buy a base, check three things: the system type (conventional or addressable), the voltage (12 V or 24 V systems both work with Series 65, but the panel must match), and whether you need any auxiliary function.

  • For a standard office or corridor with no extra devices, the standard base is sufficient.
  • If you need to switch a local sounder or a fan when the detector alarms, use the relay base.
  • If you have a long loop and want to prevent a single short from disabling the whole system, use the isolator base on an addressable loop.
  • If the detector is hidden above a ceiling tile, use the remote indicator base so you can see the alarm LED from below.

Always verify the base’s compatibility with your panel brand. While Series 65 is a generic conventional detector, some panels require a specific base resistance or diode configuration. Check the panel’s installation manual before wiring.

Installation and Common Mistakes

Installing the base is straightforward but has several pitfalls. The base must be mounted flush to the ceiling, with the arrow on the base aligned to the direction of airflow if you are in a duct or corridor. The head clicks into place with a quarter turn; if it does not click, the head is not seated correctly and may fall off.

Common installation errors:

  • Over-tightening the terminal screws, which can strip the thread or crush the wire.
  • Using the wrong gauge wire – the terminals accept up to 2.5 mm², but thinner wire may not make a solid connection.
  • Forgetting to fit the dust cover during construction – the base has a protective cap that must be removed before the head is installed.
  • Wiring the relay base incorrectly, so the relay energises in the wrong state.

After installation, test the detector with a proper aerosol test spray, not by holding a lighter near it – heat from a flame can damage the plastic and cause false alarms.

Maintenance and Cleaning

The base itself requires little maintenance, but the detector head should be cleaned periodically to prevent dust ingress from causing false alarms. To clean, remove the head by pressing the release tab and twisting anti-clockwise. Vacuum the insect screen and the optical chamber gently with a soft brush attachment. Do not use water or solvents – they will damage the electronics.

Check the base terminals for corrosion every few years, especially in humid environments. If you find green or white deposits on the terminals, clean them with a dry cloth and re-tighten. In coastal areas, consider applying a small amount of dielectric grease to the terminals to prevent corrosion.

The Series 65 range has been in production since the early 1990s, and many buildings still have these bases in service. Replacement bases are still manufactured, but if you are upgrading a system, check whether the new detector head is backward-compatible with the old base – the Series 65 head will not fit the newer XP95 or Discovery bases.

Cost and Availability

Pricing varies by supplier and quantity. A standard Series 65 base typically costs between $5 and $12 USD when bought singly, with lower prices for bulk orders. The relay and isolator bases cost more, usually $15 to $30, because of the extra components. These are not consumer items; they are sold through fire alarm wholesalers and electrical distributors, not general retail stores.

When buying, check the date code on the packaging. Apollo bases have a manufacturing date printed on the label, and older stock may have been stored for years. While the plastic does not degrade significantly, the terminal springs can lose tension over a very long time. Buy from a reputable supplier that rotates stock.

Frequently Asked Questions

Can I use a Series 65 head on an XP95 base? No. The Series 65 head and the XP95 head have different pin configurations and communication protocols. They are not interchangeable. Always match the head to the base series.

What is the difference between a diode base and a standard base? The diode base has a rectifier diode in the positive line. It is used when you need to isolate the detector from a shared positive supply or when the panel requires a specific polarity. In most modern installations, the standard base is sufficient.

Does the isolator base work with a conventional panel? No. The isolator base is designed for addressable loops only. On a conventional panel, the isolator will not function and may cause the zone to fail. Use a standard base for conventional systems.

How do I remove a detector head from the base? Press the small release tab on the side of the base while twisting the head anti-clockwise. The head will unlock and pull free. Do not pull the head straight off without twisting – you will break the locking tabs.

Can I replace just the base without changing the head? Yes, but only if the new base is the same model and series. The head will fit any Series 65 base, but if you change from a standard base to a relay base, you must rewire the terminals correctly.

Is the Series 65 base still compliant with current fire codes? The base itself is a passive component and does not expire. However, the detector head has a recommended service life of about 10 years, and some jurisdictions require replacement of the entire detector after that period. Check your local fire code for specific replacement requirements.

Related

How pages are sourced and corrected: Sources and editorial policy.