A crosscut sled holster is a shop-made or commercial accessory that holds a crosscut sled’s push block, stop block, or auxiliary fence securely against the sled’s back fence or side rail when the sled is not in use. It is not a standard factory part of most table saws; it is an organizational add-on that keeps frequently used sled components within arm’s reach and prevents them from sliding off or getting lost.
Why a Sled Holster Matters
Crosscut sleds are among the most used table saw jigs, and their accessories—especially the push block and the stop block—are small enough to misplace. A holster keeps these parts attached to the sled itself, so you do not have to search the shop or re-set a stop block every time you start a cut. For woodworkers who switch between crosscutting and rip cutting often, a holster also speeds up workflow because the push block is always exactly where you left it.
The idea is borrowed from tool belts and firearm holsters: a dedicated, friction-fit or spring-loaded pocket that holds a specific item. On a crosscut sled, the holster is usually mounted to the back fence (the tall fence that rides against the table saw’s fence) or to the left or right side rail. It is designed so that the push block or stop block can be slid in and out with one hand, without loosening any bolts.
Types of Holsters
There is no universal crosscut sled holster, but most fall into one of three categories:
- Magnetic holsters: These use rare-earth magnets embedded in a small block or strip. The push block or stop block is held against the magnet. This is the simplest type and works well if your push block has a steel base or a steel plate.
- Friction-fit wooden holsters: A wooden block with a routed or cut-out pocket that matches the profile of your push block. The block is glued or screwed to the sled’s back fence. The push block snaps in with a slight pressure fit.
- Spring-loaded or cam-lock holsters: These use a spring or a cam lever to clamp the accessory in place. They are more secure than friction-fit but take a little longer to release.
Commercial versions are rare; most woodworkers build their own holsters from scrap plywood or hardwood because the size and shape of push blocks vary so much.
How to Build a Simple Holster
You can make a basic friction-fit holster in about ten minutes. You will need a piece of hardwood or plywood about 3/4 inch thick, a router or a chisel, and wood glue or screws.
- Measure the width and thickness of your push block’s base or handle.
- Cut a block of wood that is about 2 inches longer than the push block’s gripping area.
- Route or chisel a slot in the block that matches the push block’s profile. The slot should be slightly deeper than the push block’s base, so the block sits flush.
- Sand the slot so the push block slides in with light friction—not so tight that you have to force it, and not so loose that it falls out.
- Attach the holster to the back fence of your sled with wood glue and a couple of screws from the back side. Make sure the screws do not protrude into the sled’s path.
If you use a magnetic holster, simply glue a rare-earth magnet into a recess in a small block and screw that block to the sled’s fence. Test the pull force before committing—if the magnet is too strong, you may accidentally pull the sled off the saw when you grab the push block.
Choosing a Holster for Your Sled
Before you build or buy a holster, consider these factors:
- Push block size and shape: A holster must match the exact dimensions of your push block. A one-size-fits-all holster will not work.
- Sled fence height: The holster should not extend above the fence line, or it will interfere with the workpiece or the blade guard.
- Accessibility: Place the holster on the side of the sled opposite your saw’s fence, so you can grab the push block without reaching over the blade.
- Security: The holster must hold the push block firmly enough that it does not vibrate loose during a cut.
If you have multiple push blocks or stop blocks, you might need a holster with multiple slots. Some woodworkers make a small rack that holds two or three blocks side by side.
Common Problems and Solutions
The most common issue with a crosscut sled holster is that the push block falls out during a cut. This usually happens because the friction fit is too loose or the magnet is not strong enough. The fix is to add a small rare-earth magnet to the bottom of the holster slot or to add a thin strip of rubber (like a piece of inner tube) inside the slot to increase friction.
Another problem is that the holster shifts over time due to vibration. If you use screws, check them occasionally and tighten them. If you use glue, make sure the surface is clean and clamped for at least an hour. A third issue is that the holster gets in the way of the blade guard or the riving knife. If that happens, move the holster to the front of the sled, near the handle, or to the side rail—just make sure it does not obstruct your hand path.
Holster vs. Other Storage Methods
Some woodworkers prefer to store push blocks and stop blocks in a drawer or on a pegboard near the table saw. That works, but it adds a step: you have to walk to the drawer, pick up the block, and walk back. A holster eliminates that step. However, a holster adds weight to the sled and can make it slightly more awkward to lift. If you store your sled on a wall rack, a holster with a heavy push block might make the sled unbalanced.
Another alternative is to use a magnetic strip mounted to the side of the saw cabinet. That keeps the push block off the sled but still within arm’s reach. The trade-off is that the push block is not attached to the sled, so you might forget it when you move the sled to a different saw.
Safety Considerations
When using a crosscut sled holster, always make sure the push block is securely seated before you start the saw. A loose push block can fall into the blade path. Also, never place a holster on the back fence in a position where it could be struck by the blade if the sled is pushed too far. The blade should never come within 2 inches of the holster.
If you build a holster, avoid using metal fasteners that could come into contact with the blade. Use brass screws or wood glue. Finally, check the holster regularly for cracks or wear—a cracked holster can fail mid-cut.
Frequently Asked Questions
Can I buy a crosscut sled holster?
Yes, but they are not common. Some small woodworking tool manufacturers sell universal push block holders that can be screwed to a sled, but most woodworkers make their own because the fit must be custom. Search for “push block holder” or “table saw push stick storage” and you will find a few commercial options, but expect to modify them.
Will a holster work with any push block?
No. A holster is specific to the shape and size of your push block. A magnetic holster is more forgiving because it only needs a steel surface, but a friction-fit or cam-lock holster must be made to match your exact block.
Where is the best place to mount a holster?
The most common spot is on the back fence, on the side opposite the table saw fence. This keeps the push block out of the way of the blade and the workpiece, but still within easy reach. Some woodworkers mount it on the front edge of the sled, near the handle, but that can interfere with your grip.
Does a holster affect the sled’s accuracy?
No, as long as the holster is mounted securely and does not protrude into the path of the workpiece or the blade. A properly mounted holster adds negligible weight and does not change the sled’s alignment.
Can I use a holster for a stop block?
Yes. Many woodworkers use the same holster design to hold a stop block, especially a flip stop. Just make sure the holster is sized for the stop block’s base and that the stop block does not interfere with the fence when you are not using it.
Related
- Lakes Dermatology Humboldt Iowa: Services & Info
- River Styx Pronunciation (Greek Myth)
- Lakes Dermatology Burnsville: Clinics & Services
How pages are sourced and corrected: Sources and editorial policy.