Apollo whirlpool tub training is not a formal certification but the practical process of learning to install, operate, and maintain an Apollo brand whirlpool bathtub. This guide covers the key steps for first-time owners and technicians, focusing on the specific features of Apollo models, common troubleshooting, and safety considerations.
Background: The Apollo Brand and Its Tub Lines
Apollo is a manufacturer known primarily for producing acrylic whirlpool and air-jet bathtubs for residential and light commercial use. Unlike high-end spa brands that focus on luxury features, Apollo tubs are typically positioned as mid-range, practical units with simple, reliable hydrotherapy systems. Their product lines include standard rectangular alcove tubs, corner models, and drop-in designs, most of which use a conventional pump-and-jet system rather than the more complex air-jet or ultrasonic systems found in premium competitors. Understanding which specific model you have is the first step in training, as the pump location, jet count, and control layout vary between the Apollo Signature and Apollo Comfort series, for example.
How Apollo Whirlpool Systems Work
The core of an Apollo whirlpool is a recirculating pump that draws water from the tub’s bottom drain, pushes it through a heater (on some models), and then forces it out through the wall-mounted jets. This is a wet system, meaning water remains in the pipes after use. Training must cover the operational sequence:
- Filling: Water level must be at least 2 inches above the highest jet to prevent the pump from sucking air, which causes cavitation and can damage the impeller.
- Powering on: The control panel typically has a pump toggle and an optional heater switch. The heater only activates when the pump is running and water flow is detected.
- Jet adjustment: Each jet has a rotating face that opens or closes the water flow. Closing too many jets increases pressure but strains the pump; leave at least two jets fully open.
- Draining: After use, the tub drains normally, but residual water stays in the piping. The pump must be run for 30–60 seconds with the drain open after the tub is empty to purge most of this water.
Installation Training: What You Must Know
Installing an Apollo tub is not a simple DIY project if you are new to plumbing and electrical work. The training essentials include:
- Electrical requirements: Most Apollo pumps are 120V, 15-amp circuits, but some larger models require a dedicated 240V line. The pump must be on a GFCI-protected circuit, and the connection point must be accessible for service.
- Plumbing: The pump is usually mounted on a frame beneath the tub. You must install a service access panel (often on an adjacent wall or the tub skirt) that is large enough to reach the pump and drain connections.
- Leveling: The tub must be perfectly level both lengthwise and widthwise. An unlevel tub will not drain fully, leaving standing water that can cause pump seal failure.
- Pump priming: Before first use, fill the tub above the jets, then run the pump for a few seconds, turn it off, and refill if necessary. This removes air locks in the pump housing.
Operating and Cleaning Procedures
Daily operation is straightforward, but proper cleaning is where most owners fail. Because the system is wet, biofilm and soap scum accumulate inside the pipes. The manufacturer recommends a monthly purge using a low-foaming whirlpool cleaner (not dish soap or bleach, which can damage seals and create excessive foam). The procedure is:
- Fill the tub with hot water above the jets.
- Add the recommended amount of cleaner (usually 1–2 tablespoons).
- Run the pump for 10–15 minutes.
- Drain completely, then refill with cold water and run the pump for 5 minutes to rinse.
After every use, wipe the jets and tub surface with a soft cloth. Never use abrasive cleaners on the acrylic surface, as they leave micro-scratches that harbor bacteria.
Common Problems and Troubleshooting
Training should include diagnosing the most frequent issues reported by Apollo owners:
- Pump hums but no water flow: Usually an air lock. Turn the pump off, open a jet, and briefly run the pump in 2-second bursts to release the air.
- Weak jet pressure: Check the filter screen on the pump intake (located near the bottom drain). It is often clogged with hair or debris. Clean it monthly.
- Leaking under the tub: Most leaks come from the pump-to-drain hose clamps. Tighten them, but do not overtighten, as the plastic fittings can crack.
- GFCI trips immediately: This indicates a ground fault, usually from water in the pump motor. Turn off power, remove the pump cover, and dry the connections. If it persists, the pump motor needs replacement.
Comparing Apollo to Other Whirlpool Brands
When deciding whether to train on Apollo specifically, it helps to know how they stack up against competitors like American Standard or Jacuzzi. Apollo tubs generally have fewer jets (typically 4–6) than premium brands, which means simpler maintenance and fewer parts to fail. They also use a standard off-the-shelf pump (often a Cal Spa or similar), so replacement parts are cheaper and easier to find than proprietary systems. However, Apollo models lack features like inline water heaters on most units, so the water cools noticeably during a long soak. The acrylic thickness is adequate but not as thick as higher-end brands, so the tub can flex slightly under heavy weight, which can stress the tile seal over time.
Cost, Warranty, and Where to Get Training
An Apollo whirlpool tub typically costs between $800 and $2,500 depending on the model and jet count, which is lower than the $3,000–$6,000 range for comparable Jacuzzi or Kohler units. The manufacturer offers a limited warranty (usually 5 years on the surface, 2 years on the pump), but it requires proof of professional installation in many cases. For hands-on training, options are limited: Apollo does not run its own certification program. Most plumbers and tub installers learn through general whirlpool repair training from suppliers like Plumbing & HVAC schools or by reading the service manual that ships with each unit. Online video tutorials from independent repair technicians cover the specific pump models used in Apollo tubs, which is often more useful than brand-specific training.
Safety and Hygiene Considerations
Whirlpool tubs pose two real risks: electrical shock and bacterial contamination. The GFCI outlet is non-negotiable; test it monthly with the built-in test button. Never operate the pump when the water level is below the jets, as this can cause the pump to overheat. For hygiene, the wet pipes are a known breeding ground for Pseudomonas and Legionella if not cleaned regularly. This is especially important for people with compromised immune systems or open wounds. The monthly purge with a disinfectant cleaner is not optional; skipping it for several months can result in a foul odor and skin rashes. Also, never add bath oils or bubble bath to a whirlpool tub, as they can clog the jets and cause excessive foaming that can damage the pump.
Frequently Asked Questions
Can I use regular bath bombs in my Apollo tub? No. Bath bombs contain oils, glitter, and dyes that can clog the jet nozzles and stain the acrylic. The oils also degrade the rubber seals in the pump. If you must use one, run a full cleaning cycle immediately afterward.
How often should I replace the pump on my Apollo whirlpool? With proper care, a pump typically lasts 8–12 years. The most common failure is the shaft seal, which can be replaced for about $30–$50. If the motor itself burns out, a replacement pump costs $150–$300 and is a straightforward swap if you have the same model.
Is it safe to use the whirlpool during pregnancy? Most manufacturers advise against using hot tubs or whirlpools during pregnancy, especially in the first trimester, due to the risk of overheating. The water temperature should not exceed 100°F (38°C) if you choose to use it, and you should limit sessions to 10 minutes. Consult your doctor first.
Why does my Apollo tub smell like rotten eggs? That is hydrogen sulfide gas produced by bacteria in the stagnant water in the pipes. It is a sign you have not cleaned the system frequently enough. Run a heavy cleaning cycle with a commercial whirlpool cleaner, then repeat weekly until the smell is gone. If it persists, the plumbing may need a professional flush.
Do I need a special water heater for my Apollo tub? No. The tub connects to your standard household hot water supply. The optional inline heater (if your model has one) only maintains temperature, it does not heat cold water. You must fill the tub with hot water from the tap.
Related
- Hermes of Paris Costa Mesa CA: What It Is & How to Shop
- Medusa Makeup: Styles, Symbols & How to Wear It
- Achilles Ankle Repair: Surgery, Recovery, and Risks
How pages are sourced and corrected: Sources and editorial policy.