Yes, doubling up grits—using two consecutive grits in the same sanding pass—can speed up lathe sanding, but only when done correctly: it works best for roughing and intermediate stages, not for final finishing, and it requires the right paper, speed, and technique to avoid swirls and uneven surfaces.
What Doubling Up Grits Actually Means
On a lathe, sanding is usually a sequential process: you start coarse, say 80 grit, and work your way finer to 220 or 320 for a final surface. Doubling up means you attach two different grits to the same sanding pad or use two pads simultaneously, so one pass removes material with the coarser grit while the finer grit immediately smooths the scratches left behind. The idea is to cut the number of passes in half, because each pass does two jobs at once.
This is not the same as “skip sanding” (jumping from 80 to 180, skipping 120). Doubling up is the opposite: you pair adjacent or close grits, like 80+120, 120+180, or 180+220. The coarser grit does the heavy cutting, and the finer grit refines the surface in the same sweep. It’s a technique borrowed from production turners who want to reduce cycle time without sacrificing finish quality.
How It Works on a Lathe
The physics is simple: two abrasive surfaces contact the spinning workpiece simultaneously. The coarser grit (say, 100) digs deeper, leaving scratches. The finer grit (say, 150) rides on the peaks of those scratches and knocks them down, effectively producing a surface that looks like it was sanded with the finer grit alone, but in less time.
For this to work, the two grits must be on the same flexible backing, like a padded sanding disc or a strip of cloth-backed paper folded over. You can also use a dual-grit sanding pad sold by some turning suppliers, which has a coarse side and a fine side. Alternatively, you can hold two separate pieces of paper together—coarse on the outside, fine on the inside—but that’s awkward and less effective because the fine paper doesn’t make solid contact.
The key is that the finer grit must be slightly recessed, so it only touches the high spots left by the coarser grit. If both grits press equally, the finer grit will clog quickly and the coarser grit will still dominate. That’s why most turners use a padded interface: the foam allows the fine grit to flex and ride over the surface while the coarse grit digs in.
When Doubling Up Saves Time (and When It Doesn’t)
Doubling up shines in the roughing and intermediate stages, where you’re removing tool marks and tear-out. For example, after a roughing gouge leaves a 1/16” deep spiral, you can use 80+120 to knock it down and smooth it in one pass. That can cut sanding time by 30–50% compared to sanding with 80 alone, then 120 alone.
It does not help for final finishing. Once you’re at 220 or above, the scratches are so fine that the difference between 220 and 320 is marginal, and the finer grit tends to burnish rather than cut. Also, on end grain or soft woods like pine, the finer grit can clog instantly, making the pass useless. For final grits, stick to single grit and use light pressure.
Another limitation: doubling up only works on convex or flat surfaces—the outside of a bowl, a spindle, a cylinder. On concave surfaces (the inside of a bowl), the paper must conform to the curve, and two layers of different grits don’t flex independently. You’d need a curved sanding pad with two grits, which is rare. For interiors, you’re better off with traditional sequential sanding.
How to Choose Grit Pairs
Not every pair works. The general rule is to keep the grits close—within 40–60 numbers. Common effective pairs:
- 80 + 120 for aggressive roughing
- 100 + 150 for intermediate
- 120 + 180 for pre-finish
- 180 + 220 for light smoothing
If you skip too far (80+180), the finer grit won’t remove the coarse scratches; it will just polish the bottoms of the grooves, leaving visible lines. If you use identical grits, you gain nothing. The ideal gap is about 50% of the coarser grit’s number—so 80+120 (a 40-grit gap) works, but 80+100 (a 20-grit gap) is too close to save much time.
Paper quality matters. Aluminum oxide is standard, but silicon carbide (wet/dry) cuts faster and lasts longer on hard woods. Use a stearated paper (self-lubricating) to prevent clogging, especially on resinous woods like cherry or walnut. Cloth-backed paper is more durable than paper-backed for this technique because it resists tearing when wrapped around a curved surface.
Common Problems and How to Avoid Them
The biggest issue is uneven pressure. If you press harder on one edge of the pad, the finer grit will dig in and create a shiny spot, while the coarse grit leaves a rough patch elsewhere. Solution: use a padded sanding block and keep the pad flat, moving it steadily across the surface.
Another problem is heat buildup. Two grits cutting at once generate more friction, which can burn the wood, especially on thin spindle ends. Keep the lathe speed moderate (800–1200 RPM for bowls, 1500–2000 RPM for spindles) and use light, sweeping passes. If the wood feels warm, stop and let it cool.
Clogging is also common. The fine grit loads up with dust quickly, especially on soft woods. To mitigate, use a sanding sealer before sanding, or brush the pad with a stiff nylon brush every few passes. Some turners use a vacuum attachment to pull dust away as they sand.
Finally, if you’re working on a piece with a pronounced grain (like oak or ash), the coarse grit can tear the grain, leaving a fuzzy surface that the fine grit can’t fully flatten. In that case, wet the wood slightly (raise the grain) and let it dry before sanding, or use a card scraper first.
Cost and Equipment Considerations
Doubling up doesn’t require special tools, but it does require a few extra pieces of paper. A typical 2” sanding disc costs $0.50–$1.00, and a dual-grit pad (like a 3” foam disc with 80 on one side and 120 on the other) runs $5–$15. You can also make your own by gluing two different grits of paper back-to-back with spray adhesive, but that’s messy and the adhesive can transfer to the wood.
If you already have a stash of sandpaper in various grits, doubling up costs nothing extra—you’re just using two pieces at once. The time savings are real: a production turner might save 10–15 minutes per bowl, which adds up over a day. For a hobbyist, the benefit is less about time and more about avoiding the tedium of multiple passes.
One caution: using two pieces of paper at once wears them at different rates. The coarse grit dulls faster because it does more work, so you’ll replace it more often. That can increase your consumable costs by 20–30% compared to sequential sanding. Factor that into your decision.
Safety and Technique Tips
Safety is the same as any lathe sanding: always wear a face shield or safety glasses, because sanding dust and broken paper can fly. Keep your hands clear of the spinning workpiece—use a sanding pad with a handle or a long strip of paper, not your bare fingers. Never wrap paper around your hand; if it catches, it can pull you in.
Technique-wise, start with the lathe off and the tool rest removed. Move the pad slowly from end to end, overlapping each pass by about a third. Apply even pressure—just enough to feel the coarse grit cutting. Let the paper do the work; don’t force it. After each pass, check the surface with your fingers (with the lathe off) to feel for smoothness. If you feel ridges, you’re pressing too hard on one side.
For spindles, work from the headstock to the tailstock, then reverse direction to catch any missed spots. For bowls, sand with the grain, not across it, to avoid swirl marks. And always finish with a single fine grit (like 320 or 400) to remove any remaining scratches from the coarser pair.
Alternatives to Doubling Up
If doubling up doesn’t suit your style, there are other ways to speed up lathe sanding:
- Skip sanding (e.g., 80 to 180) saves time but leaves deeper scratches; only works on soft woods.
- Power sanding with a drill-mounted disc is faster than hand sanding, but you can’t double up grits easily because the disc spins too fast.
- Scraping with a sharp cabinet scraper removes tool marks without sanding, leaving a surface that needs only a light 220 pass.
- Using a sanding mop (a wheel with multiple abrasive strips) can smooth curves quickly, but it doesn’t allow grit pairing.
Each has trade-offs. Doubling up is best for turners who want a middle ground—faster than sequential, but without the tool investment of power sanding.
Frequently Asked Questions
Can I double up grits on the inside of a bowl?
It’s difficult. The concave curve means the paper must flex to match the radius, and two layers of different grits don’t bend independently. You’d need a curved pad with two grits bonded together, which is uncommon. For interiors, stick to sequential sanding or use a power sanding disc with a single grit.
Does doubling up work on all woods?
No. It works best on hard, close-grained woods like maple, cherry, and walnut. On soft woods (pine, cedar) or woods with open grain (oak, ash), the coarse grit tears the grain and the fine grit can’t smooth it. For those woods, use a card scraper or sanding sealer first.
What’s the maximum grit gap I can use?
Generally, keep the gap under 60 grit numbers. A gap of 40–50 is ideal. If you go larger (like 80+150), the fine grit won’t remove the coarse scratches—it will just polish the valleys, leaving visible lines. If you go smaller (like 80+100), you’re not saving much time.
Will doubling up damage my lathe?
No, as long as you use reasonable speed and pressure. The extra friction is minimal. However, if you press too hard, you can stall the lathe or burn the wood. Keep the speed moderate and use light passes.
Is it worth it for a beginner?
Maybe. It saves time, but it requires more skill to get even pressure. Beginners often struggle with uneven surfaces, which doubling up can amplify. If you’re new, master sequential sanding first, then try doubling up once you’re comfortable with the lathe.
Related
- Roc Kid City: Meaning, Origin & Real-World Use
- Apollo Beach Observation Tower: Views, Tips & Facts
- Apollo Beach Liquors: What to Know Before You Go
How pages are sourced and corrected: Sources and editorial policy.