The Apollo oil tank gauge does not have a single universal manual; instead, the term covers several distinct product lines, including the Apollo ultrasonic tank level monitor, the Apollo A100 series float gauge, and the Apollo smart Wi-Fi sender. For the most common model—the Apollo ultrasonic monitor—the manual instructs you to install the sensor on the top of the tank, pair it with the receiver via a simple button press, and set the tank dimensions to get a percentage readout. Below is a breakdown of the main models, how they work, installation steps, troubleshooting, and where to find the exact PDF for your unit.
Background: What “Apollo” Actually Refers To
Apollo is a brand name used on several different oil tank gauges, which causes most of the confusion when people search for a manual. The three main types you will encounter are:
- Apollo Ultrasonic Tank Monitor: A battery-powered sensor that sits on top of the tank and measures the oil level using sound waves. It sends the reading wirelessly to a handheld receiver or a smartphone app.
- Apollo A100 Series Mechanical Gauge: A traditional float gauge that threads into the tank top. It has a dial with a red needle that moves as the float drops. No batteries or wiring.
- Apollo Wi-Fi Sender: A newer device that replaces the mechanical gauge’s top cap and sends the float position data to a home Wi-Fi network, so you can check the level from your phone.
Because the brand name is shared, the manual you need depends on which device you physically have. Check the model number printed on the side of the receiver or on the sensor itself before downloading anything.
How the Ultrasonic Monitor Works
The ultrasonic model uses a small transducer that sends a high-frequency pulse down into the tank. The pulse bounces off the surface of the oil and returns to the sensor. The time between sending and receiving the echo is converted into a distance measurement, which the device then compares to the tank’s height to calculate the percentage of oil remaining.
Key points from the manual:
- The sensor must be mounted so it points straight down into the tank, with no obstructions like a dipstick or a float arm in its path.
- The tank’s total height (from the sensor’s mounting surface to the bottom of the tank) must be entered into the receiver during setup. If you enter the wrong height, every reading will be off.
- The sensor uses a 9V battery or a lithium cell, depending on the revision. The manual warns that the battery should be replaced every 12–18 months.
- The receiver can be placed up to 100 meters (330 feet) away from the sensor in open air, but thick concrete walls will reduce that range.
Step-by-Step Setup for the Ultrasonic Model
Based on the standard Apollo manual (model numbers like AM-101 and AM-102), follow this sequence. Always confirm with your specific printed manual, as button labels vary slightly.
- Remove the existing tank cap or vent cap from the top of the oil tank.
- Place the ultrasonic sensor over the opening. It does not screw in; it sits on top and uses a rubber gasket to seal.
- Insert the battery into the sensor. The LED on the sensor should blink once.
- On the handheld receiver, press and hold the “PAIR” button for 3 seconds until the display shows a blinking antenna icon.
- Press the button on the sensor itself. The receiver will beep or show a solid antenna icon, indicating a successful link.
- Use the up/down arrows on the receiver to set the tank height in inches or centimeters. This is the internal depth of the tank, not the outside height.
- Press “SET” to save. The display will now show a percentage (e.g., 75%) instead of a distance.
If the receiver shows “LO” or “0%” immediately after setup, you likely entered the tank height incorrectly or the sensor is not pointing straight down.
Common Problems and Troubleshooting
The most frequent issues reported in Apollo manuals and owner forums are:
- No signal between sensor and receiver: Move the receiver closer to the tank and press the sensor’s button again. If it still fails, replace the battery in the sensor—low voltage is the most common cause.
- Reading stays at 100% for weeks: This usually means the sensor is pointing at the tank wall or a metal baffle inside the tank. Reposition the sensor so the beam has a clear vertical path.
- Reading fluctuates wildly: Condensation on the sensor face can distort the echo. Wipe the underside of the sensor with a dry cloth. In very cold weather, ice on the surface can also cause false echoes.
- Receiver shows “Err” or “—”: The sensor has lost pairing. Repeat the pairing procedure from scratch.
A common misconception is that the ultrasonic gauge measures the oil’s weight or density. It does not—it only measures distance. If your tank is not a simple rectangular or cylindrical shape (e.g., an underground tank that is wider in the middle), the percentage shown will not be a true volume percentage. Apollo’s manual notes this limitation and suggests using the gauge only as a “low-fuel warning” for oddly shaped tanks.
Mechanical Float Gauge (A100 Series) Manual Basics
The Apollo A100 is a simpler device. It has a threaded brass body that screws into a standard 2-inch tank opening. Inside, a float on a metal arm rises and falls with the oil level, moving a magnetic dial on the top.
Installation steps from the A100 manual:
- Clean the tank opening and remove the old gauge or cap.
- Apply thread sealant tape to the threads of the new gauge.
- Screw the gauge in by hand until snug, then tighten with a wrench another half-turn. Do not overtighten—you can crack the tank fitting.
- Check the dial: the needle should move freely when you tilt the gauge. If it is stuck, the float arm may be bent.
There is no calibration for the A100. It reads the tank level directly. The only adjustment is the length of the float arm, which is fixed at the factory. If your tank is unusually shallow, the float may hit the bottom before the needle reaches “E,” which is harmless but slightly inaccurate.
Wi-Fi Sender: Setup and App
The Apollo Wi-Fi sender replaces the top cap of a mechanical gauge. It uses the existing float arm and transmits the angle of that arm to your home router.
Setup from the manual:
- Remove the mechanical gauge’s plastic or metal top cover.
- Snap the Wi-Fi sender onto the same mounting ring, ensuring the magnet inside aligns with the float arm’s pivot.
- Download the Apollo app (available for iOS and Android).
- In the app, select “Add Device” and choose your 2.4 GHz Wi-Fi network. The sender does not support 5 GHz networks.
- Enter the tank’s total height and the sender’s calibration offset (usually provided on a sticker on the sender).
If the sender loses Wi-Fi, it will store a few days of readings and upload them when the connection returns. The manual recommends placing the sender within 15 meters (50 feet) of the router for reliable performance.
Where to Find the Exact Manual
Apollo does not host all manuals on a single public page, but the PDFs are widely available through heating supply distributors and the manufacturer’s official site. Search for the exact model number, e.g., “Apollo AM-102 manual” or “Apollo A100 instruction sheet.” Many sellers also include a printed manual in the box, so check the packaging before downloading. If you have a very old unit, contact the retailer you bought it from—they often have archived copies.
Frequently Asked Questions
Can I install an Apollo gauge myself, or do I need a professional?
For the ultrasonic and Wi-Fi models, yes, you can install them yourself. They require no electrical wiring or fuel line work—just mounting on the tank top and pairing. The mechanical A100 is also a DIY job if you are comfortable with a wrench. However, if your tank is underground or has a damaged fitting, call a heating oil technician to avoid leaks.
Why does my Apollo gauge show 50% when I just filled the tank?
This usually means the tank height setting is wrong. If you entered the external height instead of the internal depth, the gauge thinks the tank is taller than it is, so a full tank reads as half. Re-measure the inside depth from the top opening to the bottom and update the setting.
Does the Apollo ultrasonic gauge work on steel tanks?
Yes, it works on both steel and plastic tanks. The ultrasonic pulse passes through the air inside the tank, not through the tank wall, so the material does not matter. What matters is that the sensor has a clear line of sight to the oil surface.
How often should I replace the battery in the sensor?
The manual says every 12 to 18 months, depending on how often the sensor transmits. If you have the receiver set to “continuous” mode, the battery drains faster. Set the receiver to “hourly” updates to extend battery life.
My receiver shows a percentage, but I want to know how many gallons are left.
The Apollo gauge does not calculate gallons unless you enter the tank’s total capacity in the settings menu. If your tank holds 275 gallons and the gauge shows 50%, you have about 137 gallons. The manual gives a formula, but it is only accurate for rectangular or vertical cylindrical tanks.
Is the Apollo gauge compatible with all oil tanks?
No. The ultrasonic sensor needs a flat, horizontal surface on the tank top. If your tank has a curved or sloped top, the sensor will not sit level and will give false readings. The mechanical A100 requires a standard 2-inch threaded opening. Older tanks with non-standard openings will need an adapter, which Apollo does not sell.
Related
- Zeus Power Supplies LLC: Company Facts and Products
- Apollo Fish Telugu Name: Meaning & Details
- Apollo Fish in Marathi: Meaning and Name
How pages are sourced and corrected: Sources and editorial policy.