OneStopList

Gods and goddesses

Forrest Plywood Veneer Worker Blade: What It Is

Updated November 18, 2026

The Forrest Plywood Veneer Worker blade is a specialized circular saw blade designed specifically for cutting plywood and veneered panels with minimal tear-out and chip-out, producing a clean, finished edge that often requires little or no sanding.

Background and Purpose

Forrest Manufacturing, a New Jersey-based company founded in 1946, is known for its high-end woodworking blades, particularly the WWII (Wood Worker II) and the Plywood Veneer Worker. The Plywood Veneer Worker blade was developed to address a common problem in woodworking: when cutting plywood or veneered panels with a standard combination blade, the spinning teeth tend to break out the thin face veneer on the top and bottom of the cut, leaving ragged, splintered edges. This is especially problematic when cutting pre-finished plywood, melamine, or veneered MDF, where the surface layer is thin and fragile. The blade’s geometry and tooth configuration are engineered to shear the veneer cleanly rather than tear it, making it a go-to choice for cabinetmakers, finish carpenters, and hobbyists who need a ready-to-edge cut.

How the Blade Works

The Plywood Veneer Worker achieves its clean cut through a combination of design features. It typically has a high tooth count—often 80 teeth on a 10-inch blade—which means more teeth contact the material per revolution, reducing the load on each tooth and creating a finer, smoother cut. The teeth are ground with a specific hook angle (the angle of the tooth face relative to the blade’s radius) that is lower than that of a rip or general-purpose blade. A low hook angle (often around 5 degrees) makes the blade cut more slowly but with less aggressive tearing. Additionally, the blade has a triple-chip or alternate top bevel (ATB) grind. The ATB grind features teeth that are beveled alternately left and right, which slices the wood fibers cleanly on both sides of the kerf. The blade also has a thin kerf (the width of the cut) of about 0.098 inches (2.5 mm) on the 10-inch model, which reduces waste and requires less power, though it can be more prone to deflection if not fed properly.

Choosing the Right Size and Arbor

Forrest offers the Plywood Veneer Worker in several sizes to fit common table saws, miter saws, and radial arm saws. The most common sizes are 8-inch, 10-inch, and 12-inch diameters. The 10-inch blade fits most cabinet table saws and miter saws, while the 8-inch is used on portable table saws and some miter saws, and the 12-inch is for larger saws. The arbor hole (the hole in the center that mounts on the saw’s shaft) is typically 5/8-inch, but Forrest also offers blades with a 1-inch arbor for some European saws, and they can provide bushings to reduce the arbor size. When selecting a blade, you must match the diameter and arbor to your saw’s specifications. Additionally, consider the blade’s maximum RPM rating; all Forrest blades are rated for at least 7,000 RPM, which exceeds the typical table saw speed of 3,450 RPM, so that is rarely a limiting factor.

Common Problems and Solutions

Even with a high-quality blade, users may encounter issues. One common problem is burning on the cut edge, especially when feeding the wood too slowly or when the blade is not sharp. The Plywood Veneer Worker has a low hook angle, which generates more heat because it cuts slower; if you push the wood too slowly, the blade can burn the wood. The solution is to feed the material at a steady, moderate pace, letting the blade do the work. Another issue is tear-out on the bottom side of the cut, which can occur if the blade is not sharp or if the saw’s riving knife or splitter is not aligned. Using a zero-clearance insert (a throat plate with a slot exactly the width of the blade) on a table saw can also help prevent tear-out by supporting the wood fibers right at the cut line. If you are cutting melamine or laminate, the blade’s high tooth count helps, but you should also use a scoring pass or tape over the cut line for extra protection, though this is less necessary with this blade than with standard blades.

Comparison: Plywood Veneer Worker vs. WWII

Forrest’s flagship blade, the WWII (Wood Worker II), is a 40-tooth general-purpose blade that handles ripping and crosscutting in solid wood and sheet goods. The Plywood Veneer Worker, with its 80 teeth, is specifically optimized for sheet goods and veneers. The WWII is more versatile for rough construction and ripping, but it will produce more tear-out on plywood than the Plywood Veneer Worker. In contrast, the Plywood Veneer Worker excels at making clean crosscuts and miters in plywood, but it is not ideal for ripping thick hardwood because its low hook angle and high tooth count make it slow and prone to burning. Many woodworkers own both blades and switch them out depending on the task. If you primarily work with sheet goods, the Plywood Veneer Worker is the better choice; if you work with solid wood, the WWII is more practical.

Cost and Value

Forrest blades are premium products, and the Plywood Veneer Worker is priced accordingly. As of recent pricing, a 10-inch 80-tooth Plywood Veneer Worker typically retails for around $100 to $130, which is significantly more than a typical carbide-tipped blade from big-box stores (often $20–$40). The higher price reflects the quality of the carbide, the precision grinding, and the fact that Forrest blades are manufactured in the USA. They also offer a lifetime resharpening service for a fee (currently around $25–$35 per sharpening), which extends the blade’s life significantly. For a serious woodworker who makes many cuts in plywood, the cost is justified by the time saved on sanding and the quality of the finished edge. However, for a casual DIYer, a mid-priced blade with a high tooth count (like a 60-tooth ATB) may be sufficient.

Safety and Maintenance

Always follow basic saw safety when using any blade: use push sticks, keep hands away from the blade, and use a blade guard and riving knife. Because the Plywood Veneer Worker has a thin kerf, it can be more prone to deflection, so ensure your saw’s fence is parallel to the blade and use a feather board for stability. Never force the wood; let the blade cut at its own pace. For maintenance, keep the blade clean by using a blade cleaner (a solvent that dissolves resin and pitch) after heavy use. Inspect the teeth for chipping or dullness; if you notice increased tear-out or burning, it’s time to have the blade sharpened. Store the blade in its original case or a blade guard to protect the teeth.

Frequently Asked Questions

Can I use a Plywood Veneer Worker blade on a miter saw? Yes, the blade is available in 8-inch, 10-inch, and 12-inch sizes, so you can mount it on a miter saw. It works well for crosscutting plywood and trim, but be aware that the low hook angle means it cuts slower than a standard miter saw blade, so you may need to adjust your cutting speed.

What is the difference between the Plywood Veneer Worker and a standard plywood blade? The main difference is the tooth count and grind. The Plywood Veneer Worker has 80 teeth with an ATB grind, while many standard plywood blades have 60 teeth. The higher tooth count and specific grind produce a smoother cut, especially on delicate veneers, but the blade also costs more.

Does this blade work for cutting melamine? Yes, it is excellent for melamine and other coated panels. The high tooth count and ATB grind minimize chipping on the coating. For best results, use a zero-clearance insert and a steady feed rate.

How long does the blade stay sharp? With normal use on plywood and softwoods, the blade can stay sharp for several months. Forrest’s carbide tips are high-quality, but the lifespan depends on how often you use it and what you cut. When you notice increased tear-out or burning, it’s time to sharpen it. Forrest offers a sharpening service, or you can use a local sharpening shop.

Can I rip plywood with this blade? Yes, you can rip plywood, but it’s not ideal for ripping thick hardwood. The blade is designed for crosscuts and sheet goods, so ripping solid wood will be slow and may cause burning. For ripping, a dedicated rip blade or the WWII is better.

Related

How pages are sourced and corrected: Sources and editorial policy.