Yes, you can put a vise in a vise, and it is a common and practical technique in metalworking and woodworking shops. The phrase “vise in a vise” usually refers to clamping a smaller vise (like a bench vise, angle vise, or drill press vise) into the jaws of a larger vise to hold an awkward workpiece at a convenient angle, or to secure the smaller vise itself while you work on it. This article explains why and how it is done, what to watch out for, and answers common questions about using vises together.
What Is a Vise and Why Would You Stack One?
A vise is a mechanical clamp with two parallel jaws, one fixed and one moved by a screw, used to hold an object firmly while you cut, drill, file, or assemble it. The “vise in a vise” setup is used for two main reasons:
- Holding a small workpiece at an angle: A small angle vise or drill press vise can be clamped in a larger bench vise to tilt the workpiece toward you or to a specific degree for drilling or grinding.
- Working on the small vise itself: If you need to repair, modify, or clean a small vise, clamping it in a larger vise frees both of your hands.
In woodworking, a similar idea is used when a carver’s vise or a patternmaker’s vise is mounted on a workbench, but the phrase “vise in a vise” specifically refers to the act of clamping one vise within another.
How to Clamp a Vise in a Vise Safely
Doing this correctly prevents damage to both vises and the workpiece. Follow these steps:
- Choose the right sizes: The smaller vise should fit comfortably between the jaws of the larger vise, with at least an inch of clearance on each side. If it is too tight, you risk cracking the larger vise’s casting.
- Protect the jaws: Use soft jaws (made of rubber, plastic, or leather) or pieces of wood on the larger vise’s jaws. This prevents marring the smaller vise’s metal and gives a better grip.
- Position the smaller vise: Place the smaller vise so its base is flat against the larger vise’s jaw or work surface. For angled work, use a protractor or angle gauge to set the desired tilt before tightening.
- Tighten gradually: Tighten the larger vise’s handle with moderate force. Over-tightening can distort the smaller vise’s frame or crack the larger vise’s jaws.
- Check stability: Give the smaller vise a firm tug. It should not move or rock. If it does, re-adjust and tighten again.
Common Problems and How to Avoid Them
The most frequent issue is the smaller vise slipping or rotating when you apply force. This happens because the contact area is small and the clamping force is not enough. Solutions include:
- Using a piece of non-slip rubber (like an inner tube) between the two vises.
- Placing a wooden block under the smaller vise’s base to keep it level.
- Tightening the larger vise more, but only if the jaws are not at their limit.
Another problem is damaging the smaller vise’s screw or slide. If you clamp the smaller vise by its dynamic jaw (the one that moves), you can bend the screw. Always clamp the smaller vise by its fixed jaw or its base.
Choosing the Right Vise for Stacking
Not every vise is suitable for being clamped in another. Consider these factors:
- Material: Cast iron vises are strong but brittle; a sudden impact can crack them. Forged steel vises are more forgiving. Avoid clamping a lightweight aluminum vise in a heavy-duty steel vise.
- Jaw width: A wider jaw on the larger vise distributes the clamping force better. A 4-inch or 6-inch bench vise is a good base for a 2-inch or 3-inch drill press vise.
- Base shape: Vises with a flat, square base are easier to clamp securely. Round bases can roll and are harder to hold.
- Swivel base: If the smaller vise has a swivel base, lock it before clamping. Otherwise, the swivel joint may loosen and the vise will rotate unexpectedly.
Vise in a Vise vs. Other Holding Methods
Sometimes a “vise in a vise” is not the best option. Alternatives include:
- Clamps: C-clamps or bar clamps can hold a workpiece directly to the bench, which is often simpler and faster.
- Vacuum vises: For small electronic parts, a vacuum vise holds the piece without any mechanical pressure.
- Magnetic chucks: On a drill press or milling machine, a magnetic chuck can hold ferrous parts without a vise at all.
- Workholding fixtures: For repetitive tasks, a custom fixture is more accurate than stacking vises.
The “vise in a vise” method is best when you need a temporary, adjustable setup and do not want to buy a dedicated tilting table.
Safety and Accuracy Tips
Working with two vises increases the risk of pinching or flying debris. Always wear safety glasses. Keep your fingers clear of the jaws when tightening. When drilling or hammering, the smaller vise can act as a lever, so use light strokes. For accurate angle work, measure the angle with a digital protractor rather than guessing. Also, be aware that the extra height of the stacked vises raises the workpiece, which may require adjusting the height of your drill press or grinding wheel.
Cost and What to Buy
You do not need a special “vise in a vise” product. Any two vises that fit together will work. A decent 4-inch bench vise costs around $50–$100, and a small 2-inch drill press vise costs $20–$40. If you are buying a vise specifically for stacking, look for one with a flat, smooth base and no sharp edges. Used vises from garage sales are often fine, but check for cracks and a straight screw.
Frequently Asked Questions
Can I use a woodworking vise in a metalworking vise?
Yes, but be careful. Woodworking vises often have wooden jaws that can be damaged by the metal jaws of a larger vise. Use a piece of scrap wood between them to protect the wooden faces.
Will clamping a vise in a vise damage either one?
Only if you over-tighten or clamp on a weak point. Always clamp on the fixed jaw or base, and use protective jaw caps. If you hear cracking sounds, stop immediately.
What is the maximum angle I can achieve?
You can tilt the smaller vise to any angle up to about 45 degrees before it becomes unstable. Beyond that, the center of gravity shifts and the smaller vise may slip.
Is there a better way to hold a small vise on a workbench?
If you only need the small vise occasionally, a “vise in a vise” is fine. For frequent use, consider mounting the small vise on a separate wooden base that you can clamp to the bench with a quick-release clamp.
Can I put a drill press vise in a bench vise?
Yes, this is one of the most common uses. It allows you to drill holes at an angle without buying a tilting drill press table. Just make sure the drill press vise is locked and the bench vise is tightened enough to hold it securely.
Related
- Apollo Tile Company: History, Products, and Buying Guide
- Apollo Bagels Order Online: How It Works & What to Know
- Travel RN Jobs: How They Work & What to Know
How pages are sourced and corrected: Sources and editorial policy.