Yes, you can spray varnish over lacquer, but only if the lacquer is fully cured and the surface is properly prepared; otherwise, the varnish may peel, bubble, or fail to adhere. The key is understanding the difference between these two finishes and following the right preparation steps.
Lacquer vs. Varnish: The Core Difference
Lacquer and varnish are both popular wood finishes, but they cure in fundamentally different ways. Lacquer is a solvent-based finish that dries by solvent evaporation. Its molecules simply settle as the solvent evaporates, forming a film. Varnish, on the other hand, is an oil- and resin-based finish that cures by a chemical reaction with oxygen (oxidation). This means varnish forms a tougher, more durable film that is more resistant to water, heat, and chemicals.
Because of these different curing mechanisms, lacquer is generally easier to apply and dries faster, but it is less durable. Varnish takes longer to dry but offers superior protection. This is why you might want to spray varnish over lacquer: to get the durability of varnish on top of a lacquer base coat.
Why You Might Want to Spray Varnish Over Lacquer
There are several practical reasons you might consider this combination:
- Enhanced durability: Lacquer is prone to scratches and water rings. A varnish topcoat can provide a harder, more protective surface.
- UV protection: Some varnishes contain UV inhibitors that can help prevent the lacquer underneath from fading or yellowing.
- Repairing a damaged lacquer finish: If you have a piece of furniture with a scratched or dull lacquer finish, you might want to apply a varnish topcoat to restore and protect it.
- Changing the sheen: Varnish comes in a variety of sheens, so you can use it to adjust the gloss level of a lacquer finish.
Preparation: The Make-or-Break Step
The success of spraying varnish over lacquer hinges almost entirely on surface preparation. Lacquer is a relatively smooth, non-porous surface. Varnish needs a bit of “tooth” to grip onto. Without proper preparation, the varnish will not adhere well and will likely peel or flake off.
Here are the essential preparation steps:
- Ensure the lacquer is fully cured. This is critical. Lacquer can take weeks to fully cure, even if it feels dry to the touch. If you apply varnish over uncured lacquer, the solvents in the varnish can reactivate the lacquer, causing it to wrinkle or blush. A good rule of thumb is to wait at least two weeks after the last coat of lacquer.
- Clean the surface. Use a tack cloth or a lint-free cloth with a mild solvent like mineral spirits to remove any dust, grease, or fingerprints.
- Lightly sand the surface. Use a very fine grit sandpaper (e.g., 320-grit or finer) to scuff the lacquer. This creates microscopic scratches that give the varnish a mechanical bond. Be careful not to sand through the lacquer to the wood underneath. After sanding, wipe away the dust with a tack cloth.
- Apply a primer or sealer (optional but recommended). Some professionals recommend applying a shellac-based primer or sealer before the varnish. Shellac adheres well to both lacquer and varnish, acting as a bridge between the two. This is especially useful if you are unsure about the compatibility of your specific products.
Compatibility and Testing
Not all varnishes are created equal. Oil-based varnishes are the most traditional and are generally compatible with lacquer. Water-based varnishes (also called polyurethane) can also work, but they are more finicky. They are less likely to adhere to a smooth, oily surface, so proper sanding is even more critical.
Before committing to the entire project, it is always a good idea to do a test patch. Spray varnish on a small, inconspicuous area of the lacquered piece. Let it dry completely, then test the adhesion by trying to scratch it off with your fingernail. If it peels off easily, the varnish is not adhering. If it stays put, you are good to go.
Common Problems and How to Avoid Them
Even with proper preparation, you can run into issues. Here are a few common problems and their solutions:
- Fish-eye: This is when the varnish forms small, crater-like depressions. It is usually caused by contamination on the surface, such as silicone or oil. To avoid this, clean the surface thoroughly with a degreaser or a solvent like denatured alcohol before sanding.
- Bubbling: Bubbles in the varnish can be caused by shaking the can too vigorously or applying the varnish too thickly. To prevent this, stir the varnish gently, and apply thin, even coats.
- Peeling or flaking: This is the most serious problem and is almost always due to inadequate surface preparation. If you see peeling, you will need to strip the varnish and start over, paying close attention to the sanding and cleaning steps.
- Wrinkling: This can happen if the varnish is applied over a lacquer that is not fully cured. The solvents in the varnish can soften the lacquer, causing it to wrinkle. Always wait for the lacquer to cure completely.
Alternative Approaches
If you are not comfortable spraying varnish over lacquer, there are a few alternatives you might consider:
- Use a lacquer-based topcoat: This is the safest option. Lacquer is designed to be applied over itself, so you can simply add more coats of lacquer to build up a protective finish. You can also buy lacquer with added UV inhibitors or a higher solids content for extra durability.
- Strip and refinish: If the lacquer is in poor condition, it may be better to strip it off completely and start fresh with a varnish finish. This is more labor-intensive but will give you the most reliable result.
- Use a gel varnish: Gel varnishes are thicker and are designed to be wiped on rather than sprayed. They can be applied over lacquer with less risk of adhesion problems, but they are not as durable as sprayed varnish.
Frequently Asked Questions
Can I spray water-based polyurethane over lacquer?
Yes, you can, but it is riskier than using an oil-based varnish. Water-based polyurethane does not adhere as well to smooth, non-porous surfaces. You must sand the lacquer thoroughly and clean it well. A test patch is highly recommended before proceeding.
How long should I wait before spraying varnish over lacquer?
You should wait at least two weeks, and ideally longer, for the lacquer to fully cure. If you apply varnish too soon, the solvents can reactivate the lacquer, causing it to wrinkle or blush. Check the lacquer manufacturer’s instructions for specific cure times.
Do I need to use a primer between lacquer and varnish?
It is not strictly necessary, but it is highly recommended, especially if you are unsure about compatibility. A shellac-based primer acts as a barrier and provides a good bonding surface for both the lacquer and the varnish.
What grit sandpaper should I use to scuff the lacquer?
Use a very fine grit, such as 320-grit or higher. The goal is to create a dull, matte surface, not to remove the lacquer. Sanding with too coarse a grit will leave scratches that will show through the varnish.
Can I spray varnish over a lacquer that has been waxed?
No, you cannot. Wax will prevent the varnish from adhering. You must remove all wax from the surface before sanding and applying varnish. Use a wax remover or a solvent like mineral spirits to clean the surface thoroughly.
Related
- Clamping Edge Banding: How It Works & When to Use It
- Reader Tales of Reviving Batteries
- Best Mortising Bits: Top Picks & Buying Guide
How pages are sourced and corrected: Sources and editorial policy.