OneStopList

Gods and goddesses

Sharpening Grinding Jig Buffers: How They Work

Updated November 18, 2026

Sharpening grinding jig buffers are not a single tool but a combination of three components—a grinding machine, a jig that holds the blade at a fixed angle, and a buffing wheel or strop—used together to produce a consistent, polished edge. The jig ensures the bevel angle stays constant, the grinding wheel removes metal efficiently, and the buffer (or strop) refines the edge to a razor finish. This article explains how these parts work together, how to choose them, and common mistakes to avoid.

What Is a Grinding Jig?

A grinding jig is a device that holds a blade (chisel, plane iron, knife, or scraper) at a precise, repeatable angle while you present it to a grinding wheel or belt. Without a jig, your hands naturally vary the angle by a degree or two, which creates a convex or uneven bevel. Jigs come in two main types:

  • Fixed-angle jigs—the blade is clamped and the whole assembly rides on a guide bar or rests on the tool rest; the angle is set by adjusting the projection of the blade or the height of the base.
  • Pivot-style jigs—the blade rotates around a pivot point, so the angle changes as you swing it; these are common on bench grinders.

Most woodworking jigs (e.g., the Veritas Mk.II or the Eclipse style) use a guide bar that rolls on the grinder’s tool rest. The distance from the bar to the grinding wheel determines the bevel angle—closer to the wheel gives a steeper angle. For example, a chisel with a 25° bevel might have the blade projecting 1-1/2 inches from the jig, while a 30° bevel would project less. The exact numbers vary by jig design, so always check the manufacturer’s instructions.

How the Grinding Wheel Removes Metal

Grinding wheels are made of abrasive grains (aluminum oxide, silicon carbide, or diamond) bonded together. When the wheel spins at 3,450 RPM (typical for a bench grinder), each grain acts like a tiny cutting tooth. The coarser the grit, the faster it removes metal but the rougher the finish. For sharpening, you generally want a wheel between 80 and 220 grit. A 100-grit wheel is a good all-purpose choice for chisels and plane irons.

Two critical factors affect grinding quality:

  • Wheel speed—too fast and the steel overheats, ruining the temper (hardness). Most bench grinders run at 3,450 RPM, which is fine for high-speed steel but risky for carbon steel if you press hard. Slower grinders (1,750 RPM) are safer for beginners.
  • Cooling—dip the blade in water frequently or use a wheel with a soft bond that breaks down and exposes cool grains. Never let the steel turn blue or straw-colored; that indicates overheating.

A jig helps because it keeps the blade moving steadily across the wheel, preventing localized heat buildup. But even with a jig, you must let the blade cool between passes.

Buffing Wheels and Compounds

After grinding, the edge has a burr (a thin wire of metal) that must be removed. Buffing is one way to do that. A buffing wheel is a soft cloth or felt wheel that spins at high speed (often on a separate arbor or a bench grinder with a buffer attachment). You apply a polishing compound—typically a green chromium oxide or a white aluminum oxide bar—to the wheel, then gently press the blade’s bevel against it.

Buffing does two things:

  • It removes the burr and polishes the bevel to a mirror finish, which reduces friction when cutting.
  • It can slightly round the edge if you press too hard or hold the blade at the wrong angle. That’s why a jig is useful even for buffing—some jigs have a flat plate that lets you maintain the exact bevel angle.

However, buffing is not the same as honing. Honing (using a fine stone or strop) produces a sharper edge because it creates a micro-bevel that is more acute. Buffing can actually dull a very fine edge if the wheel is too soft or the compound is too coarse. Many woodworkers skip buffing entirely and go straight to a leather strop charged with fine compound.

Choosing the Right Jig for Your Tools

Not all jigs fit all tools. Consider these factors:

  • Blade width—a chisel jig may not clamp a wide plane iron. Some jigs have adjustable jaws that open up to 2-1/2 inches or more.
  • Bevel angle range—most jigs allow 20° to 45°, but if you sharpen carving tools with very low angles (15°), check the limits.
  • Grinder compatibility—the jig’s guide bar must fit your grinder’s tool rest. Some tool rests are too thick or too thin; you may need to shim or modify.
  • Ease of setup—a jig that takes five minutes to set up each time is less likely to be used. Look for one with a built-in angle gauge or a stop that you can set once.

For knives, a different type of jig (like a Lansky or a Wicked Edge) holds the blade stationary and moves the stone. Those are not grinding jigs but sharpening systems. If you want to use a bench grinder for knives, you need a knife-specific attachment that clamps the spine and lets you set the angle.

Common Problems and How to Avoid Them

Even with a jig, things go wrong. Here are the most frequent issues:

  • Overheating—the #1 mistake. Solution: use light pressure, keep the blade moving, and dip in water every few seconds.
  • Uneven bevel—if the jig is not clamped squarely, one side of the bevel will be wider. Check with a marker: coat the bevel with a felt-tip pen, make one pass, and see where the grind removes the ink.
  • Burr not removed—after grinding, you must hone the back (flat side) of the blade to remove the burr. Buffing alone may not do it. Use a fine stone or strop.
  • Wheel loading—soft steel can clog the wheel with metal. Use a dressing tool (a diamond dresser or a star wheel) to clean the wheel surface.
  • Jig slipping—if the clamp loosens during grinding, the angle changes. Tighten firmly, but not so hard that you dent the blade.

If you see sparks flying in a continuous stream, you’re pressing too hard. A light touch with many passes is better than one heavy pass.

Safety and Shop Practices

Bench grinders are dangerous if used carelessly. Always wear safety glasses or a face shield—wheels can shatter, and metal fragments fly. Never grind on the side of a wheel; use the face. Keep the tool rest within 1/8 inch of the wheel to prevent the blade from being pulled in. And never use a grinding wheel that is cracked or wobbles.

When buffing, wear a dust mask because the compound creates fine particles. Also, tie back long hair and remove loose clothing—the wheel can catch them. Some compounds (like those containing chromium) are toxic if inhaled, so work in a well-ventilated area.

Alternatives to Buffing

Buffing is optional. Many craftsmen achieve a razor edge without it. Alternatives include:

  • Honing stones—water stones or oil stones in fine grits (4000–8000) produce a polished edge.
  • Strops—leather or canvas charged with fine abrasive (e.g., chromium oxide) is the classic final step.
  • Sandpaper—adhesive-backed sandpaper on a flat surface (the “scary sharp” method) works from 400 to 2000 grit.

Buffing is best for removing a burr quickly or for polishing a bevel for aesthetics, but it does not replace honing. For a truly sharp edge, you need to form a micro-bevel with a fine stone or strop after grinding.

Frequently Asked Questions

Can I use a buffing wheel on the same grinder as my grinding wheel?

Yes, many bench grinders have two shafts—one for a grinding wheel and one for a buffing wheel. But the speed is usually the same (3,450 RPM), which is fine for buffing. Just make sure the buffing wheel is rated for that speed and that you use a separate tool rest or none at all (buffing is done freehand).

What angle should I sharpen a chisel?

For general woodworking, 25° is standard. For paring chisels (light cuts), 20° is better. For mortising chisels (heavy work), 30° is recommended. The jig lets you set the angle precisely and repeat it.

Why does my edge dull faster after using a grinding jig?

If you grind to a coarse grit (e.g., 80), the edge has a “sawtooth” finish that dulls quickly. Always follow grinding with honing on a fine stone or strop to smooth the edge. Also, if you overheated the steel, the temper is ruined, and the edge will dull quickly regardless of how you finish it.

Do I need a special jig for carving tools?

Yes, carving tools have curved edges and require a jig that can rotate the blade or use a slack belt. Some jigs have a “carving” attachment that holds the tool at a fixed angle while you rotate it. Alternatively, you can use a flat stone and freehand, but the jig gives consistency.

Is a slow-speed grinder worth the extra cost?

If you sharpen carbon steel tools, a slow-speed grinder (1,750 RPM) is safer because it reduces the risk of overheating. High-speed steel (HSS) can handle higher speeds, but even then, a slow grinder is more forgiving. If you already have a fast grinder, you can use a CBN (cubic boron nitride) wheel, which runs cooler.

Related

How pages are sourced and corrected: Sources and editorial policy.