OneStopList

Gods and goddesses

Saw Dovetail Tail Boards: How to Cut Them

Updated November 17, 2026

Saw dovetail tail boards are the fan-shaped pins cut into the end of a board that interlock with matching sockets on the adjoining board in a dovetail joint. In woodworking, the “tails” are the flared, trapezoidal projections, and cutting them accurately with a saw is the first step to a strong, gap-free joint. This article explains what tail boards are, how to lay them out and saw them, and how they differ from pin boards.

What Are Dovetail Tails and Pin Boards?

A dovetail joint connects two boards at a right angle, most commonly in drawer construction, boxes, and carcass work. The joint has two parts: the tails (the fan-shaped projections) and the pins (the matching sockets). The tail board is the one with the tails cut into its end; the pin board has the sockets that receive them.

In a through dovetail, both the tails and the pins are visible from the outside of the joint. In a half-blind dovetail, the tails are hidden inside the socket, so only the pins show on the front face. The tails are always cut first, because they are used to mark the pin locations on the mating board.

Traditional dovetails are cut by hand with a dovetail saw, a chisel, and a marking gauge. The angle of the tails is typically 1:6 for softwood and 1:8 for hardwood, though many woodworkers use a single angle for all work. The tails are cut on the end grain of the board, and their slope provides mechanical strength that resists pulling apart.

How to Lay Out Dovetail Tails

Before sawing, you must lay out the tails accurately. The process begins with marking the thickness of the pin board onto the end of the tail board using a marking gauge. This line, called the baseline, defines the depth of the tails.

  1. Set the marking gauge to the thickness of the pin board and scribe a line across the end grain and down both faces of the tail board.
  2. Decide on the spacing and number of tails. A common rule is to place a half-tail at each edge, then space the full tails evenly across the width.
  3. Mark the tail angles with a sliding bevel or a dovetail template. For a 1:8 slope, set the bevel to 7.1°; for 1:6, use 9.5°.
  4. Draw the tails on the end grain, then carry the lines down both faces to the baseline.

Many woodworkers mark the waste areas with an X or a scribble so they do not cut the wrong side of the line. Accurate layout is critical because the tails are used to transfer the pattern to the pin board.

Sawing the Tails: Step-by-Step

Once the layout is complete, sawing the tails is a matter of cutting to the baseline while keeping the saw plate vertical. The board is held in a vise, usually with the end tilted upward at a comfortable angle.

  1. Clamp the tail board in a vise with the end grain facing up and slightly toward you.
  2. Use a dovetail saw (typically 15-20 TPI) with a stiff back. Start the cut on the waste side of the line, just inside the marked angle.
  3. Cut down the angled line, keeping the saw perpendicular to the face of the board. Do not cut past the baseline.
  4. Repeat for each tail. For the half-tails at the edges, cut only one side.
  5. Remove the waste between the tails with a coping saw or fret saw, cutting close to the baseline.
  6. Chisel out the remaining waste to the baseline, using the waste side of the line as a guide.

The key to clean tails is a sharp saw with minimal set, and a steady hand. The saw should follow the layout line exactly; any deviation will show as a gap in the final joint.

Common Mistakes and How to Avoid Them

Even experienced woodworkers make errors when sawing dovetails. The most frequent problems are:

  • Cutting past the baseline: This creates a gap at the bottom of the joint. Avoid by stopping the cut just short of the line and finishing with a chisel.
  • Angled cuts: The saw must stay vertical relative to the face of the board. If it tilts, the tails will be wedge-shaped and the joint will not close.
  • Cutting on the wrong side of the line: Always cut on the waste side. Cutting on the line makes the tails too small, leaving gaps.
  • Uneven spacing: Inconsistent tail widths look sloppy. Use a marking gauge or dividers to lay out equal spaces.
  • Broken tails: Thin tails can snap if the saw wanders or if you chisel too aggressively. Leave a little extra material and pare to the line.

If a tail is slightly too large, you can trim it with a chisel or file. If it is too small, the joint will be loose; some woodworkers glue in a shim, but it is better to recut the board.

Choosing the Right Saw and Angle

The dovetail saw is the most important tool. It has a thin blade, a stiff back, and fine teeth that cut on the push stroke. Saws with 15 to 20 teeth per inch (TPI) are typical for dovetails; finer teeth give a smoother cut but are slower.

The angle of the tails affects both strength and appearance. A steeper angle (like 1:6) is stronger in softwood because the short grain is less likely to break. A shallower angle (1:8) is more elegant and is preferred for hardwood. Many woodworkers use a single angle, often 1:7, for all work to simplify setup.

When choosing a saw, consider the handle comfort and the blade thickness. A thinner blade (0.015″ or less) removes less material and is easier to control. Western saws cut on the push; Japanese saws cut on the pull and have no set, which can produce a finer cut but require a different technique.

Dovetail Tails vs. Pin Boards: Which to Cut First?

In traditional dovetail joinery, the tails are always cut first. The reason is that the tails are used to mark the pin locations on the mating board. By placing the tail board on the end of the pin board and scribing around each tail, you transfer the exact pattern.

Cutting the pins second allows you to fit them to the tails. If the pins are slightly too large, you can trim them with a chisel. If the tails were cut second, you would have to adjust the tails, which is more difficult because they are already shaped.

Some woodworkers cut the pins first for half-blind dovetails, but the standard practice remains tails first. The tails are also easier to saw because the layout is on the end grain, which is flat and easy to mark.

Safety and Accuracy Tips

Hand sawing dovetails is safe if you follow basic precautions:

  • Always clamp the work securely. A moving board can cause the saw to slip.
  • Keep your fingers clear of the saw path. Use a bench hook or a vise to hold small pieces.
  • Use a sharp saw. Dull teeth require more force and are more likely to wander.
  • Wear safety glasses to protect against sawdust and debris.
  • When chiseling, cut away from your body and keep both hands behind the cutting edge.

For accuracy, practice on scrap wood first. Mark the baseline clearly and check that your saw is square to the face. A small square or a dovetail guide can help keep the saw vertical. Many woodworkers use a magnifying lamp to see the layout lines clearly.

Frequently Asked Questions

What is the difference between a tail board and a pin board?

The tail board has the fan-shaped tails cut into its end. The pin board has the matching sockets (pins) that receive the tails. In a through dovetail, both are visible; in a half-blind, the tails are hidden.

What angle should I use for dovetail tails?

Common angles are 1:6 (about 9.5°) for softwood and 1:8 (about 7.1°) for hardwood. Many woodworkers use a single angle like 1:7 for all work. Steeper angles are stronger in softwood; shallower angles look more refined.

Why do my dovetail joints have gaps?

Gaps usually come from cutting on the wrong side of the line, sawing past the baseline, or the saw tilting. Check that your saw is vertical and that you cut just on the waste side of the line. Practice on scrap to refine your technique.

Can I cut dovetails with a power tool?

Yes, you can use a router with a dovetail jig, or a CNC machine. Power tools are faster and more consistent, but many woodworkers prefer hand-cut dovetails for their craftsmanship and the ability to fit the joint precisely.

How do I fix a tail that is too small?

If a tail is too small, the joint will be loose. You can glue in a thin shim and recut, or you can recut the entire board. It is often easier to start over than to repair a poorly cut tail.

What saw is best for a beginner?

A 15 TPI dovetail saw with a comfortable handle is a good start. Japanese pull saws are also popular because they are thin and easy to control. Choose one that feels balanced in your hand and practice on softwood first.

Related

How pages are sourced and corrected: Sources and editorial policy.