Yes, you can sand woodturning projects with a lubricant, and doing so often improves the finish and reduces dust, but it requires the right technique and the correct type of lubricant for the stage of sanding you are in.
Why Sand With a Lubricant?
Sandpaper works by cutting wood fibers with abrasive grit. When you sand dry wood, the friction generates heat, which can burn the surface, especially on thin-walled turnings like bowls or hollow forms. Heat also causes the wood to expand and then contract, leading to tiny cracks or a raised grain that feels rough after finishing. A lubricant dissipates that heat, keeps the abrasive from clogging with resin and dust, and helps the sandpaper glide smoothly over the surface. The result is a finer, more consistent scratch pattern and a surface that feels silky to the touch.
Lubricated sanding is common in other woodworking disciplines—like sanding between coats of finish with a bit of oil—but in turning it is a specialized technique. Many turners use it only for the final grits (400 and above) because the lubricant can leave a residue that interferes with some finishes. Others use it from the start with a specific lubricant that evaporates completely.
What Lubricants Work for Sanding Turnings?
Not all lubricants are safe or effective for woodturning. The most common choices are:
- Mineral oil – Food-safe and non-drying, it lubricates well but leaves a residue that must be wiped off thoroughly before applying a film finish like lacquer or polyurethane.
- Danish oil or boiled linseed oil – These are drying oils that can be used as a sanding lubricant and then become part of the finish. They are often used for oil-and-wax finishes, but they will affect the color of the wood and take time to cure.
- Water – Simple water works as a lubricant and raises the grain, which you then sand down. It is free and leaves no residue, but it can cause rust on your lathe bed and may cause the wood to swell, so it is best used on already-sealed or stabilized wood.
- Commercial sanding lubricants – Products like Sand-Rite or Myland’s Sanding Sealer are formulated to reduce friction and evaporate quickly, leaving a clean surface. These are often the safest choice for a finish-ready surface.
Never use silicone-based lubricants or waxes containing silicone, as they cause fisheye in finishes and are nearly impossible to remove completely.
How to Sand With a Lubricant
The technique is straightforward, but the order matters:
- Start with dry sanding at a lower grit (e.g., 120 or 150) to remove tool marks and shape the surface.
- Once you reach about 220 grit, apply a small amount of lubricant to the wood—either directly on the spinning surface or on the sandpaper. Use a rag or brush to spread it evenly.
- Sand with the lathe at a slow to medium speed (around 500–1000 RPM for a 6-inch bowl) to avoid flinging the lubricant.
- Move through the grits (220, 320, 400, 600) using light pressure. The lubricant will pick up dust and turn into a slurry, which helps polish the wood.
- Wipe off any excess lubricant with a clean cloth before it dries. If using a drying oil, let it cure as per the manufacturer’s instructions before applying a topcoat.
Always sand with the grain where possible, though on a spinning bowl the grain direction is constantly changing, so you simply move the paper across the surface in a smooth, even motion.
Pros and Cons of Lubricated Sanding
The main advantage is the improved surface quality. The lubricant prevents the abrasive from loading up with resin, which is a big problem with oily woods like teak or cocobolo. It also reduces the amount of fine dust in the air, which is a health benefit. The downside is the mess—lubricant can splatter, and you have to clean the lathe and tools afterward. Also, if you use a non-drying lubricant like mineral oil, it can seep into the wood and cause problems with certain finishes. For example, if you apply a water-based polyurethane over mineral oil, it may not adhere properly. For that reason, many turners reserve lubricated sanding for the final finish coats or for pieces that will be finished with the same oil.
Common Problems and How to Avoid Them
The most frequent issue is leaving too much lubricant on the surface. Excess oil can cause the wood to look blotchy, especially on light-colored woods like maple or birch. To avoid this, use a small amount—just a few drops on a pad—and wipe off thoroughly after each grit. Another problem is sanding too fast: the heat from high speed can break down the lubricant and cause it to gum up the paper. Keep the lathe speed moderate and let the abrasive do the work. If you are using water, be careful not to let it sit on the wood too long, as it can raise the grain excessively and cause the wood to crack as it dries. Finally, always test your lubricant on a scrap piece of the same wood to see how it affects the finish before applying it to your project.
Lubricant vs. Dry Sanding: Which Is Better?
There is no universal answer—it depends on the wood and the finish you plan to use. For open-pored woods like oak or ash, dry sanding is often sufficient because the coarse grain gives the finish something to grip. For dense, closed-pore woods like maple or cherry, lubricated sanding can produce a glass-smooth surface that feels almost polished. If you are going to apply a film finish like lacquer or shellac, dry sanding is usually safer because you avoid any risk of contamination. If you are using an oil finish, lubricated sanding with the same oil is a classic technique—it fills the pores and gives a deep, even sheen. Many turners use a hybrid approach: dry sand up to 400 grit, then apply a sanding sealer, and then do a final wet-sand with a lubricant at 600 grit to polish the sealer.
Safety and Cleanup
Lubricants can be slippery, so keep a rag handy to wipe up spills immediately. Never wear loose clothing or gloves while sanding, as they can get caught in the lathe. When using oil-based lubricants, be aware that oily rags can spontaneously combust—store them in a sealed metal container or spread them out to dry flat. Wear a dust mask even when wet-sanding, as the slurry can still contain fine particles that are harmful to breathe. After sanding, clean the lathe bed and tool rest with a degreaser to remove any oily residue.
Frequently Asked Questions
Can I use WD-40 as a sanding lubricant?
WD-40 is not recommended because it contains silicone and other additives that can contaminate the wood and cause finish adhesion problems. It is better to use a dedicated sanding lubricant or a plain mineral oil.
Do I need to use a lubricant for every sanding grit?
No. Most turners use it only for the finer grits (320 and above) because the lower grits are meant to remove material quickly, and the lubricant can clog the coarse paper and slow down the process.
Will lubricated sanding make the wood too oily for glue?
If you are using a non-drying oil like mineral oil, it can seep into the wood and prevent glue from penetrating. For pieces that will be glued, dry sand or use a drying oil that cures completely.
What is the best lubricant for a food-safe bowl?
Mineral oil is food-safe and the most common choice for salad bowls. After sanding with mineral oil, wipe off the excess and let it soak in for a few hours. You can then apply a food-safe wax or leave it oiled.
Can I use water on a lathe without damaging it?
Water can cause rust on the lathe bed and other metal parts. If you use water, wipe down the lathe immediately after sanding and apply a light coat of paste wax to protect the metal.
Related
- Chemist Warehouse Nail Polish: Brands, Prices & Tips
- Festool CT Cyclone: Do You Need One?
- We’ve Gone Finishing? Meaning & Origins
How pages are sourced and corrected: Sources and editorial policy.