OneStopList

Gods and goddesses

Routing Curved Corners Jig: How to Use One

Updated November 17, 2026

A routing curved corners jig is a template or guide that holds a router at a fixed offset from a workpiece so you can cut a consistent, smooth radius on a corner instead of a sharp 90-degree edge. You use it by clamping the jig to the board, running the router’s bearing or bushing against the jig’s edge, and letting the bit remove the material inside the curve.

Why You Need a Curved Corner Jig

Hand-routing a curved corner freehand almost always produces a wobbly, uneven arc because the router wants to follow the grain and your hands cannot hold a perfect radius. A jig solves that by giving the router a rigid, curved path to follow. The same jig also lets you repeat the identical radius on multiple corners, which matters for furniture, drawer fronts, and any project where matching curves are part of the design.

Beyond consistency, a jig is safer. A router kicking against a clamped guide is far less likely to lurch than one being pushed through a freehand cut. It also lets you use a larger bit than you could safely control by hand, so you can cut a 2-inch radius in one pass instead of nibbling away at it.

How a Curved Corner Jig Works

Most curved corner jigs are simple L-shaped or rectangular templates with a quarter-circle cut out of one corner. The radius of that cutout is the radius you want on the workpiece, minus the offset between the router’s bearing and the bit’s cutting edge. If you use a flush-trim bit with a top bearing, the bearing rides against the jig’s edge and the bit cuts exactly to the jig’s shape. If you use a bushing, the offset is the distance from the bushing’s outer edge to the bit’s cutting edge, so the jig’s radius must be larger by that amount.

To use it:

  • Clamp the jig firmly onto the workpiece so the curved cutout sits exactly over the corner you want to round.
  • Choose a bit with a bearing that matches the jig’s radius, or install the correct guide bushing.
  • Set the router’s depth so the bit cuts through the workpiece but not into your bench.
  • Start the router, then lower it into the material at the flat end of the curve, and push it along the jig’s edge in a clockwise direction (for a right-handed router) so the bit’s rotation pulls it against the guide.
  • Make multiple shallow passes if the wood is thick or the radius is large, raising the bit a little each pass.

The result is a clean quarter-circle corner that matches the jig exactly. For a corner on a tabletop or shelf, you would typically route from the top face, but for a raised panel or a piece that will be flipped, you may need to route from both sides.

Choosing a Jig: Commercial vs. Shop-Made

You can buy a commercial curved corner jig, but many woodworkers make their own from 1/2-inch or 3/4-inch plywood or MDF. A shop-made jig is cheap and can be sized exactly to the radius you need. The key is to make the cutout perfectly smooth and to use a bearing-guided bit so the router follows the edge without catching.

When choosing a jig, consider:

  • Radius range: Some jigs have a single fixed radius; others are adjustable, letting you slide a pivot or a curved arm to change the size of the arc.
  • Material: A jig made from solid wood or phenolic resin will last longer and stay true than one made from thin MDF that can swell or chip.
  • Clamping: Look for a jig with built-in clamps or at least flat surfaces where you can attach your own clamps without interfering with the router’s path.
  • Base size: A larger base gives the router more stability, but it also makes the jig heavier and harder to position on small workpieces.

For occasional use, a simple shop-made jig is often the best choice. For production work, a commercial adjustable jig can save time if you frequently change radii.

Common Problems and How to Avoid Them

The most common issue is tear-out at the start or end of the cut, especially on cross-grain corners. To avoid it, climb-cut the first pass (move the router in the opposite direction of normal rotation) so the bit shears the fibers cleanly, then make a final conventional pass. Another frequent problem is the router tipping as it enters the curve, which happens when you lower it straight down onto the corner. Instead, start the router with the bit fully retracted, then plunge it into the waste area just outside the curve and feed it into the jig’s edge.

If the cut is rough or burning, the bit is likely dull or the feed rate is too slow. A sharp carbide bit and a steady, moderate feed will give a clean cut. Also check that the bearing is clean and spins freely; a gummed-up bearing will leave a burn mark along the edge.

Finally, if the jig shifts during the cut, you get a stepped corner. Always clamp the jig securely, and for large workpieces, add a clamp near the corner you are routing, not just on the far ends.

Comparing a Jig to Other Methods

A curved corner jig is not the only way to round a corner. You can also use a router with a trammel (a pivot arm) to swing an arc, a jigsaw or bandsaw to rough-cut the curve and then sand it smooth, or a rasp and sandpaper for a small radius. The jig is superior when you need a precise, repeatable radius on many identical pieces. A trammel is faster for a single large radius, but it leaves a pivot hole in the waste that you must remove. A jigsaw is fine for rough work but leaves a faceted edge that requires significant sanding.

For small radii (under 1/4 inch), a simple round-over bit with a bearing is easier than a jig because it cuts the curve directly on the edge. A jig becomes the better choice when the radius is larger than the largest round-over bit you own, or when you want a full quarter-circle that goes all the way through the corner rather than just a rounded edge.

Safety and Accuracy Tips

Routing curved corners is safe if you follow standard router practices. Always wear safety glasses and hearing protection, and use a router with a stable base. Never remove the guard or the dust-collection port if your router has one. Keep your hands away from the bit and use push sticks or clamps to hold small pieces.

For accuracy, measure the offset between the bearing and the bit before you make the jig. If you are using a bushing, the offset is the distance from the bushing’s outer edge to the bit’s cutting edge, and you must add that to the desired radius when cutting the jig’s template. Test the setup on a scrap piece first to confirm the radius matches your drawing. If it is slightly off, adjust the jig or the bushing rather than forcing the router.

Also, be aware of grain direction. Routing with the grain (from the end of the board toward the middle) gives a cleaner cut than routing against it. On a corner, the grain direction changes, so you may need to make a climb-cut pass first to avoid tear-out, as mentioned earlier.

Frequently Asked Questions

Can I use a straight bit instead of a flush-trim bit? Yes, but you must use a guide bushing and the jig’s radius must be adjusted for the bushing offset. A flush-trim bit with a bearing is simpler because the bearing rides directly on the jig, so the bit cuts exactly to the template’s shape.

What size router do I need? A trim router (1/4-inch collet) can handle small radii and thin material, but a full-size router (1/2-inch collet) is better for large radii and thick stock because it has more power and a larger base for stability.

How do I make a jig for a specific radius? Trace the radius on a piece of plywood using a compass or a trammel, cut it out with a jigsaw, and sand the edge smooth. The cutout’s radius should be your desired radius minus the bearing offset (or plus the bushing offset, depending on the guide you use).

Can I route a curved corner on a board that is already assembled? Yes, but you need to clamp the jig securely to the assembled piece and be careful not to route into any adjacent parts. It is often easier to route the corners before assembly, but a jig works either way.

Why does my cut have a small flat spot at the start? That happens if you plunge the router straight down into the corner. Instead, start the router in the waste area just outside the curve and feed it into the jig’s edge so the bit enters the material gradually.

Is a curved corner jig the same as a round-over template? No. A round-over template guides a bit that cuts a quarter-round profile on the edge of a board, leaving a rounded edge but not changing the corner’s shape. A curved corner jig cuts a full radius that removes the sharp corner entirely, creating a rounded corner on the face of the board.

Related

How pages are sourced and corrected: Sources and editorial policy.