OneStopList

Gods and goddesses

Imp Wall Anchors? How They Work & When to Use Them

Updated November 17, 2026

Imp wall anchors are a brand of self-drilling drywall anchors designed to hold screws in hollow walls without a pre-drilled pilot hole or a stud. They are commonly sold in hardware stores and are used for mounting lightweight to medium-weight items like curtain rods, towel bars, and small shelves directly into drywall.

What Are Imp Wall Anchors?

Imp wall anchors are a type of threaded plastic anchor. Unlike a standard plastic expansion anchor that requires you to drill a hole first, an Imp anchor has a sharp, screw-like point and coarse threads that cut into drywall as you drive it in with a screwdriver or drill. The anchor itself is hollow, so after it is seated flush with the wall, you insert a standard screw into the center. The screw expands the anchor against the back of the drywall, creating a firm grip.

The name “Imp” comes from the manufacturer, ITW (Illinois Tool Works), which produces them under the “Imp” brand. They are also sometimes called “self-drilling drywall anchors” or “screw-in anchors.”

How Do Imp Anchors Work?

The key to an Imp anchor is its design. The outer threads are deep and sharp, so when you turn the anchor, it cuts its own hole through the drywall. The tip is pointed to help start the thread without slipping. Once the anchor is fully inserted, the head sits flat against the wall surface. Then you drive a screw into the center of the anchor. The screw’s threads engage with the inner walls of the anchor, and as the screw goes deeper, it forces the anchor’s body to expand outward, pressing against the back side of the drywall. This expansion distributes the load over a larger area than a simple nail or screw would, which is why the anchor can hold more weight.

Imp anchors are designed for drywall thicknesses of 1/2 inch (standard) or 5/8 inch. They are not intended for plaster, tile, or masonry. The installation process is straightforward:

  • Mark the spot on the wall.
  • Position the anchor point against the drywall.
  • Drive the anchor in with a Phillips screwdriver or a drill with a bit, turning clockwise until the head is flush.
  • Insert the screw and tighten until snug—do not overtighten, as this can strip the anchor.

How Much Weight Can They Hold?

The weight capacity of an Imp anchor depends on the size and the condition of the drywall. A typical small Imp anchor (about 1/2 inch long) might hold 20–30 pounds in 1/2-inch drywall when used with a proper screw. Larger versions can hold up to 50 pounds or more. However, these ratings assume the anchor is installed correctly, the drywall is in good condition, and the load is static (not pulled outward). Pull-out forces, such as someone yanking on a towel bar, reduce the effective capacity. It’s always safer to use a stud for anything heavy, like a large mirror or a TV mount.

How to Choose the Right Size

Imp anchors come in a few sizes, usually labeled by the screw gauge they accept (e.g., #6, #8, #10). The package will state the recommended screw size and the maximum load. Here’s a simple guide:

  • Light loads (under 10 lbs): small anchors for #6 screws—good for small hooks, picture frames, or lightweight curtain rods.
  • Medium loads (10–25 lbs): #8 screws—suitable for towel bars, toilet paper holders, or small shelves.
  • Heavier loads (25–50 lbs): #10 screws—for larger shelves, coat racks, or small cabinets.

If you’re unsure, check the anchor packaging for a weight chart. Also consider the screw length: it should be long enough to pass through the item you’re mounting and into the anchor without bottoming out.

Common Problems and Misconceptions

One common mistake is using an Imp anchor in plaster or lath walls. The threads will tear the plaster, and the anchor won’t grip properly. Another issue is overtightening the screw, which can strip the internal threads and cause the anchor to spin freely. If that happens, the anchor is ruined and must be removed, leaving a larger hole.

A frequent misconception is that Imp anchors are “self-tapping” for metal studs. They are not—they are for drywall only. For metal studs, you need a special self-tapping screw or a toggle bolt. Also, some people think that once the anchor is in, you can remove it and reuse it. In practice, removing the screw often damages the anchor, so it’s best to treat them as single-use.

Comparison to Other Anchors

Imp anchors are just one of many drywall anchor types. Here’s how they compare:

  • Plastic expansion anchors (molly bolts): These require a pre-drilled hole and expand behind the wall. They are similar in strength but take more time to install.
  • Toggle bolts: These have a spring-loaded wing that opens behind the wall. They hold much more weight (up to 100+ lbs) but require a larger hole and are harder to remove.
  • Self-drilling metal anchors: These are similar to Imp but made of metal. They are stronger and can sometimes be used in thinner metal studs, but they are more expensive.
  • Winged plastic anchors: These have plastic wings that fold out. They are easier to remove but not as strong as Imp anchors for the same size.

For most household jobs, Imp anchors offer a good balance of ease and holding power, especially if you don’t want to drill a pilot hole.

Cost and Where to Buy

Imp anchors are inexpensive. A pack of 20–50 anchors typically costs $3–$8 at home improvement stores like Home Depot, Lowe’s, or online retailers. They are often sold in the fasteners aisle. Because they are so cheap, it’s a good idea to buy a few extra in case you make a mistake or need to remount an item.

Safety and Installation Tips

  • Always check for electrical wiring or pipes behind the wall before drilling or driving an anchor. Use a stud finder that also detects live wires.
  • Wear safety glasses when driving anchors, as the tip can snap off if you hit a hard spot.
  • Do not use Imp anchors in ceilings for anything heavier than a small light fixture—drywall anchors are not rated for overhead loads that could fall.
  • If you’re mounting something that will be subject to frequent pulling (like a hand towel ring), consider using a toggle bolt for extra security.
  • When driving the anchor, keep it straight. If it goes in at an angle, it may poke out the back of the drywall and not hold.

Frequently Asked Questions

Can I use Imp anchors in plaster walls?
No. Imp anchors are designed for drywall only. Plaster is too hard and brittle; the anchor will crack the plaster and fail to grip. For plaster, use a plaster hook or a toggle bolt with a drilled hole.

Do I need to pre-drill a hole for an Imp anchor?
No, that’s the main advantage. The anchor is self-drilling, so you can drive it directly into drywall. However, if your drywall is very hard or you’re near a stud, you might need to apply extra pressure or drill a tiny pilot hole to get started.

How do I remove an Imp anchor without damaging the wall?
Unscrew the anchor counterclockwise with a screwdriver. It will leave a small hole that you can fill with spackle. If the anchor is stuck, you can push it into the wall cavity, but that creates a bigger hole.

What screw size do I use with an Imp anchor?
Check the package—each anchor is sized for a specific screw gauge (e.g., #6, #8, #10). Using a screw that’s too large will split the anchor; too small won’t engage the threads.

Can I use Imp anchors in a stud?
You can, but it’s not necessary. If you hit a stud, the anchor may not go in easily because the wood is denser. It’s better to use a regular wood screw directly into the stud, which will hold more weight.

Are Imp anchors reusable?
Generally, no. Once you remove the screw, the anchor may deform or strip. It’s best to replace the anchor if you need to remount something in the same spot.

Related

How pages are sourced and corrected: Sources and editorial policy.