OneStopList

Gods and goddesses

HP 6V2 Dado Kits: What They Are & How to Use

Updated November 18, 2026

HP 6V2 dado kits are replacement blade sets for the HP 6V2 table saw, a model sold by Harbor Freight. These kits typically include two stacked dado blades and a set of shims, allowing you to cut grooves and rabbets. This article explains what these kits contain, how they work, and what to consider before buying one.

Background: The HP 6V2 Table Saw

The HP 6V2 is a 10-inch bench-top table saw sold under Harbor Freight’s Chicago Electric and later Bauer brands. It is a budget-friendly saw popular with DIYers and hobbyists. The saw uses a 5/8-inch arbor, which is the standard size for most 10-inch table saws in North America. Because it is an inexpensive saw, many owners look for affordable accessories, including dado stacks.

What a Dado Kit Contains

A typical HP 6V2 dado kit includes:

  • Two outer blades (each about 1/8 inch thick) that cut the sides of the groove.
  • Four to six inner chipper blades (each about 1/8 inch thick) that remove the waste material between the outer blades.
  • A set of shims (thin metal or plastic washers) that allow you to fine-tune the width of the cut.

When assembled on the arbor, the stack width determines the groove width. For example, using two outer blades and four chippers gives a width of about 3/4 inch (two 1/8-inch outers plus four 1/8-inch chippers = 6/8 inch, or 3/4 inch). Adding shims can increase this width slightly, up to the maximum capacity of the arbor.

How a Dado Stack Works

A dado stack cuts a flat-bottomed groove in one pass. Unlike a standard saw blade that makes a thin kerf, a dado stack is a set of blades that together create a wider cut. The outer blades score the sides of the groove, while the chippers remove the material in between. The shims allow you to adjust the width precisely, from about 1/4 inch up to the maximum width the saw can handle.

To use a dado stack, you remove the standard saw blade and install the dado stack on the arbor. The stack must be assembled in the correct order: outer blade, chippers, outer blade, with shims placed between them as needed. The arbor nut is then tightened securely. The saw’s riving knife and blade guard must be removed for dado work, which is a safety consideration—many table saws have a specific dado throat plate that you must install to support the wider cut.

Choosing a Dado Kit for the HP 6V2

When selecting a dado kit for the HP 6V2, consider the following factors:

  • Arbor size: The HP 6V2 uses a 5/8-inch arbor. Ensure the kit is designed for 5/8-inch arbors. Most dado stacks come with a 5/8-inch arbor hole, but some may have a 1-inch hole with a bushing.
  • Maximum width: The saw’s arbor length limits the maximum stack width. Most 10-inch table saws can handle a 3/4-inch dado stack, but some can only accept 1/2 inch. Check your saw’s manual.
  • Blade diameter: The HP 6V2 uses 10-inch blades. Dado stacks are typically 8 inches in diameter, which is standard for 10-inch table saws. An 8-inch stack is fine because it still cuts deep enough for most joinery.
  • Quality: Cheap kits may have blades that dull quickly or warp. Look for carbide-tipped blades, which last longer than steel.

Common Problems and Misconceptions

A common misconception is that any dado stack will fit any table saw. In reality, the arbor length and the saw’s horsepower matter. The HP 6V2 has a 15-amp motor (about 2 horsepower), which is sufficient for a 3/4-inch dado in softwoods, but may struggle with hardwoods. Another issue is that the saw’s arbor may not be long enough to accept a full 3/4-inch stack plus the nut. Some users report that a 3/4-inch stack fits, but the nut only catches a few threads, which is unsafe. Always check that the arbor nut engages at least half the threads.

Another problem is that the HP 6V2’s throat plate is not designed for dado stacks. You must use a zero-clearance throat plate or a dedicated dado insert to prevent the workpiece from falling into the gap. Many owners make their own zero-clearance insert from plywood.

Comparison: Stacked Dado vs. Wobble Dado

There are two main types of dado cutters: stacked dado sets and wobble dado blades. A stacked dado set (like the HP 6V2 kits) consists of multiple blades that cut a precise flat-bottomed groove. A wobble dado is a single blade that is tilted on the arbor to cut a wider groove. Wobble dados are less expensive but produce a slightly concave bottom and are less accurate. For the HP 6V2, a stacked set is the better choice for clean joinery, but it is more expensive.

Cost and Where to Buy

HP 6V2 dado kits are typically sold at Harbor Freight or online marketplaces like Amazon and eBay. Prices range from $30 to $80, depending on the brand and quality. Harbor Freight sells a 10-inch, 8-inch diameter dado set under its Chicago Electric brand for around $40. Higher-end sets from Freud or DeWalt cost more but offer better precision and durability.

Safety Considerations

Using a dado stack is inherently more dangerous than a standard blade because the cut is wider and the blade is exposed. Always follow these safety rules:

  • Remove the riving knife and blade guard, and install a zero-clearance throat plate.
  • Use a push stick or push block to feed the workpiece, especially for narrow cuts.
  • Never reach over the spinning blade.
  • Ensure the arbor nut is tightened securely before starting the saw.
  • Wear eye and hearing protection.
  • Do not attempt to cut a groove wider than the stack’s maximum rated width.

Frequently Asked Questions

Can I use a 6-inch dado stack on the HP 6V2?

Yes, but the arbor hole must be 5/8 inch. A 6-inch stack will work, but it will limit the maximum depth of cut. The HP 6V2 can handle an 8-inch stack, which is the standard size for 10-inch saws.

How wide can a dado stack cut on the HP 6V2?

The maximum width depends on the arbor length. Most 10-inch table saws can handle a 3/4-inch stack, but some HP 6V2 owners report that a 3/4-inch stack leaves only a few threads for the nut. Check your saw’s manual or measure the arbor length before buying.

Do I need a special throat plate for dado cuts?

Yes, you should use a zero-clearance throat plate or a dedicated dado insert. The standard throat plate has a wide opening that can cause the workpiece to drop or the cut to be uneven.

Can I use a dado stack on a jobsite saw?

Many jobsite saws, including the HP 6V2, can accept a dado stack, but the motor may struggle with wide cuts in hardwoods. Also, some saws have a shorter arbor that cannot accept a 3/4-inch stack. Always check the manual.

What is the difference between a dado and a rabbet?

A dado is a groove cut across the grain, while a rabbet is a groove cut along the edge of a board. Both can be cut with a dado stack, but a rabbet requires the blade to be positioned so that it cuts only part of the width.

Is a wobble dado safer than a stacked dado?

No, a wobble dado is generally considered less safe because it has a larger exposed blade surface and can be more difficult to control. A stacked dado set is more predictable and is preferred by most woodworkers.

Related

How pages are sourced and corrected: Sources and editorial policy.