Finishing turned pens is the process of applying a protective and aesthetic coating to a wooden pen blank after it has been shaped on a lathe. The right finish not only enhances the wood’s natural beauty but also protects it from the oils, moisture, and wear of daily handling.
Why Finishing Matters for Turned Pens
Unlike larger turned objects like bowls, pens face unique challenges. They are constantly handled, slipped in and out of pockets, and exposed to skin oils and minor impacts. An unfinished or poorly finished pen will quickly dull, absorb moisture, and may even crack. A proper finish seals the wood, brings out the grain, and provides a smooth, durable surface that feels pleasant to write with. The finish also affects the pen’s appearance—glossy, satin, or matte—and can dramatically change how the wood’s color and figure are perceived.
Types of Finishes for Turned Pens
There are several popular finish types, each with its own application method, durability, and look. Choosing one depends on your experience level, the desired sheen, and the time you want to invest.
- CA (Cyanoacrylate) Glue Finish: Often called “super glue” finish, this is the industry standard for high-gloss, durable pen finishes. Thin CA is applied in multiple coats, building a glass-like layer that is very resistant to moisture and wear. It dries quickly and can be polished to a deep shine. Requires good ventilation and care to avoid sticking to fingers.
- Friction Polish: A blend of shellac and wax (like Hut Ultra Gloss or Mylands) applied while the lathe spins. The friction of the cloth melts the polish, creating a warm, satin sheen. It’s fast and easy but less durable than CA, making it better for pens that won’t see heavy use.
- Wax Finish: Paste or liquid wax (like carnauba or beeswax) applied after a sanding sealer. It gives a soft, natural feel and a low-luster shine. Wax alone offers minimal protection and needs reapplication, but it’s simple and safe.
- Oil Finish: Penetrating oils like Danish oil or tung oil soak into the wood, highlighting the grain. They provide a natural, matte look and moderate protection. They require longer curing times and multiple coats, and they don’t build a surface film, so the wood can still absorb moisture over time.
- Shellac: A traditional finish applied as a liquid or as a friction polish. It dries quickly and gives a warm, amber tone. Shellac is not waterproof and can be damaged by alcohol, so it’s less common for pens unless used under a topcoat.
Step-by-Step: Applying a CA Finish
Because CA glue is the most popular and durable choice, here’s a typical process. Always work in a well-ventilated area and wear protective gloves.
- Sand the blank: Sand the turned pen blank progressively through grits from 220 to 600 or higher, using a sanding sealer or friction polish to stabilize the wood. Remove all sanding dust.
- Apply the first thin coat: With the lathe running at a slow speed (around 500-800 RPM), apply a small drop of thin CA glue to a paper towel or foam applicator. Spread it evenly along the blank, moving from one end to the other. The glue will soak in quickly.
- Accelerator (optional): Spray a light mist of CA accelerator to cure the glue instantly. This speeds up the process but can cause a frosted look if overused.
- Build up coats: Repeat steps 2-3 for 4-6 coats, allowing each to dry. Some turners apply medium or thick CA for the final coats to build a thicker film.
- Polish the finish: Once the CA is fully cured (wait at least 15 minutes), wet-sand with high grits (1000, 2000, 3000, 4000) and then polish with a plastic polish or micromesh pads to achieve a high gloss.
- Final buff: Use a soft cloth or a buffing wheel with a fine abrasive compound to bring out the ultimate shine.
Common Problems and How to Avoid Them
Even experienced turners encounter issues with pen finishes. Here are common pitfalls and their solutions.
- Bubbles in CA finish: Caused by applying too much glue at once or using an old bottle. Apply thin coats and use fresh CA. You can also use a foam brush to spread the glue evenly.
- Frosty or white spots: Usually from overusing accelerator. Use less accelerator or let the glue dry naturally for a few minutes.
- CA sticking to fingers: Always wear nitrile gloves. If you do get glue on your skin, use acetone (nail polish remover) to dissolve it.
- Uneven or blotchy finish: This often happens with oily woods like cocobolo or rosewood. Wipe the blank with acetone before finishing to remove surface oils, and use a sanding sealer.
- Finish peeling or chipping: The finish wasn’t adhered properly, or the wood wasn’t clean. Ensure you sand to a high grit and clean the blank with a tack cloth before applying the finish.
Comparing CA vs. Friction Polish vs. Oil
The choice of finish often comes down to trade-offs between durability, appearance, and ease of application.
- Durability: CA glue is the most durable and water-resistant. Friction polish is moderate and can wear off with heavy use. Oil finishes are the least protective but are easy to repair.
- Appearance: CA gives a high-gloss, plastic-like finish that can mask the wood’s natural feel. Friction polish imparts a warm, satin sheen that feels more natural. Oil penetrates and highlights the grain, giving a low-luster, natural look.
- Application speed: Friction polish is the fastest, taking just a few minutes. CA takes about 15-20 minutes including drying. Oil requires multiple coats over several days.
- Repairability: Oil and friction polish are easy to reapply to a worn area. CA is difficult to repair without stripping the entire finish.
Safety and Health Considerations
Finishing pens involves chemicals that require caution. Always read the label on your products.
- Ventilation: CA glue and solvents release fumes that can irritate eyes and lungs. Work in a well-ventilated area or use a respirator with organic vapor cartridges.
- Skin protection: CA glue bonds skin instantly. Wear nitrile gloves, not latex, which can stick. Keep acetone nearby for emergencies.
- Fire hazard: CA glue and some oils are flammable. Keep them away from open flames and hot surfaces. Dispose of oily rags in a metal container with a lid.
- Dust: Sanding wood creates fine dust that is harmful to breathe. Use a dust mask or a vacuum system.
Frequently Asked Questions
How many coats of CA glue should I put on a pen?
Typically, 4-6 thin coats are sufficient for a durable finish. Some turners apply up to 10 coats for a thicker, glass-like appearance, but this requires more polishing to achieve a smooth surface. The key is to use thin coats and let each one cure fully.
Can I use a friction polish on a pen that will be used daily?
Yes, but it will wear off over time. Friction polish is a good choice for pens that are displayed or used occasionally. For daily use, a CA finish is more durable and will resist moisture and oils better. You can also apply a wax over a friction polish to add a bit more protection.
Why does my CA finish look cloudy or white?
Cloudiness usually comes from moisture trapped under the finish or from using too much accelerator. Make sure the wood is completely dry and clean before applying CA. Also, apply accelerator sparingly—a light mist is enough. If the cloudiness persists, you may need to sand off the finish and start over.
Do I need to sand the pen blank before finishing?
Yes, sanding is crucial. Start with 220 grit and work up to at least 600 grit. For oily woods, go to 800 or higher. Smooth sanding removes tool marks and creates a uniform surface for the finish to adhere to. Always wipe off the dust with a tack cloth.
What is the best finish for a beginner?
Friction polish is the easiest for beginners because it’s fast, forgiving, and doesn’t require special safety precautions. However, it’s not as durable. If you want a durable finish, CA glue is worth learning, but practice on scrap wood first to get the hang of applying it without bubbles or sticking.
How do I get a high-gloss finish on a pen?
To achieve a high gloss, you need a buildable finish like CA glue. After applying multiple coats and letting them cure, wet-sand with micromesh pads from 1500 to 12000 grit, then polish with a plastic polish or a buffing compound. The final step is a clean, soft cloth to buff out any remaining haze.
Related
- Lakes Federal Credit Union Monticello Indiana: Full Guide
- Laurel Wreath Logo: Meaning and History
- Styx River ATV Park: Trails, Rules, and What to Know
How pages are sourced and corrected: Sources and editorial policy.