OneStopList

Gods and goddesses

Eliminating Snipe Jointer: Causes & Fixes

Updated November 17, 2026

Yes, jointer snipe can be eliminated or minimized to a barely visible level by using proper feed technique, setting the tables correctly, and in severe cases, adding a shop-made snipe board or using a jointer with a cutterhead lock. Snipe is a slight dip or depression at the start or end of a board caused by the cutterhead removing more material when the workpiece is not fully supported by both tables.

What Causes Jointer Snipe

Snipe happens when the outfeed table is set too low, when the board tips or rocks as it enters or leaves the cutterhead, or when the pressure you apply changes the board’s position. On a jointer, the outfeed table must be exactly level with the cutterhead’s highest point; if it is even a few thousandths of an inch low, the board drops onto the cutterhead at the end of the pass, and you get a dip. Similarly, at the start, if the infeed table is too high relative to the outfeed, the board will pivot as it crosses the cutterhead, cutting a deeper groove at the beginning.

Another common cause is uneven hand pressure. Many woodworkers push down hard on the outfeed side once the board is halfway across, which lifts the trailing end and lets the cutterhead take a deeper bite. The same happens if you lift the board slightly when starting a pass. Even a well-adjusted jointer can show snipe if you rock the board while feeding.

How a Jointer Cuts and Where Snipe Forms

A jointer works by spinning a cutterhead with knives or inserts that protrude slightly above the outfeed table. The infeed table is set lower by the depth of cut you want. As you push a board across, the infeed table supports the wood before the cut, and the outfeed table supports the freshly cut surface after the cutterhead. Snipe occurs at the two transition points: when the board’s leading edge first contacts the cutterhead and when the trailing edge leaves it.

At the start, the board is only supported by the infeed table until it reaches the cutterhead. If the outfeed table does not catch the leading edge immediately and level, the board tips downward, and the cutterhead removes extra wood from the first inch or two. At the end, the board is only supported by the outfeed table once the trailing edge passes the cutterhead. If the outfeed table is low, the board drops, and the cutterhead takes a deeper cut on the last inch or two.

Step-by-Step Fixes for Snipe

Before you buy any accessories, try these adjustments and techniques. Most snipe can be reduced or eliminated with careful setup and consistent feed.

  • Set the outfeed table level with the cutterhead. Use a straightedge (a metal ruler or a known-flat board) placed on the outfeed table and extending over the cutterhead. Rotate the cutterhead by hand; the highest point of the knives or inserts should just touch the straightedge. Adjust the outfeed table until it is exactly at that height.
  • Check the infeed table height. The infeed table should be lower than the outfeed table by the depth of cut you want. If it is too high, the board will pivot at the cutterhead and create a deeper cut at the start. Set it to your desired depth (usually 1/16 inch or less for most work).
  • Use even, consistent pressure. Keep your hands flat and push down evenly on both sides of the board as it crosses the cutterhead. Do not lift the trailing end or press down harder on the outfeed side. Practice feeding with a steady rhythm.
  • Feed the board without stopping. A pause mid-pass can cause the board to settle or rock, creating a dip. Keep the board moving at a constant speed.
  • Use a snipe board or auxiliary board. Clamp or tape a thin, flat board (like 1/4-inch plywood) to the top of the workpiece, extending beyond both ends. This gives the jointer tables extra support, so the workpiece does not tip. The sacrificial board takes the snipe instead of your workpiece.
  • Consider a jointer with a cutterhead lock. Some newer jointers have a mechanism that locks the cutterhead height during the pass, preventing any vertical movement that could cause snipe. This is a feature to look for if you are buying a new machine.

Common Snipe Problems and Misconceptions

One common misconception is that snipe is only caused by a low outfeed table. In reality, a high infeed table or uneven hand pressure can cause snipe even when the outfeed table is perfect. Another misconception is that you can eliminate snipe by slowing down the feed rate. Slower feeding does not fix snipe; it only makes the cut smoother. The cause is always related to support or table alignment.

Another frequent issue is that snipe appears only on one end of the board. If you see snipe only at the start, check the infeed table height and the transition to the outfeed. If you see it only at the end, check the outfeed table level. If you see it on both ends, the outfeed table is likely low, or you are lifting the board at both ends.

Some woodworkers think that using a jointer with a spiral cutterhead eliminates snipe. It does not; spiral cutterheads reduce tearout and noise, but they still cut a circle, and the same support issues apply. Snipe is a geometry problem, not a knife sharpness problem.

How to Choose a Jointer That Minimizes Snipe

If you are in the market for a jointer, look for features that make snipe control easier. A longer bed (at least 6 feet for a 6-inch jointer) gives more support for long boards, reducing tipping. A parallelogram-style infeed table (instead of dovetailed ways) holds its setting better over time, which helps maintain the correct height. Some jointers have a quick-set cutterhead lock or a built-in snipe prevention system, such as a micro-adjustable outfeed table or a spring-loaded bridge that holds the board down.

Also consider the cutterhead type. While it does not prevent snipe, a helical or spiral cutterhead with indexable inserts is easier to adjust if you ever need to set the knives. Traditional straight knives require careful setting to ensure they are all at the same height; if one knife is higher, it will cut deeper and create a ridge or snipe-like effect. If you buy a used jointer, budget for new knives or inserts and take the time to set them properly.

Cost and Time Considerations

Fixing snipe on an existing jointer costs nothing if it is just a matter of adjusting the tables. You only need a straightedge and a wrench. If you need to replace worn knives or inserts, the cost varies: a set of straight knives for a 6-inch jointer might cost $20–$50, while a set of indexable inserts for a spiral head can be $50–$100 or more. A shop-made snipe board is just a scrap piece of plywood, so it is essentially free.

If you decide to buy a new jointer with snipe-reducing features, expect to pay more. A basic 6-inch jointer with dovetailed ways might cost $300–$500, while a model with parallelogram tables and a cutterhead lock can cost $800–$1,200. The price difference is worth it if you do a lot of edge jointing for glue-ups, but for occasional use, a well-adjusted budget jointer can produce snipe-free results with careful technique.

Safety and Accuracy Tips

When adjusting your jointer, always unplug it first. The cutterhead is sharp, and you should never reach near it while the machine is plugged in. Use a push block or push stick to keep your hands away from the cutterhead, especially when jointing narrow or short pieces. Never joint a board shorter than 12 inches without a push block, as your fingers can easily slip into the cutterhead.

For accuracy, always check the outfeed table with a precision straightedge, not just a regular ruler. A machinist’s straightedge is ideal, but a known-flat piece of aluminum or glass can work. Rotate the cutterhead to find the highest knife, and adjust the table so that the knife just kisses the straightedge. After setting, run a test piece and check for snipe with a straightedge or by feel. If you still see a dip, recheck the table heights and your hand pressure.

When feeding, keep your body balanced and your hands on the board, but do not press down excessively. The jointer should do the work; you are only guiding the board. If you find yourself forcing the board, the tables may be out of alignment, or the knives may be dull, which can also cause burning or chatter.

Alternatives to a Jointer for Edge Jointing

If you do not have a jointer or cannot eliminate snipe, there are alternative ways to get a straight edge. A table saw with a jointing jig (a sled that holds the board against a straight fence) can produce a straight edge, though it is slower. A router table with a straight bit and a fence can also joint edges, but it is less accurate for long boards. A hand plane, such as a No. 7 or No. 8 jointer plane, is the traditional tool and can produce a perfectly straight edge with practice. For rough work, you can use a circular saw with a straightedge guide, but the edge will not be as clean.

Each method has trade-offs in speed, accuracy, and cost. A jointer is the fastest for long boards, but a hand plane is quiet and does not require electricity. If you only joint a few boards a year, a hand plane might be all you need.

Frequently Asked Questions

Can snipe be completely eliminated?

Yes, with perfect table alignment and consistent hand pressure, you can reduce snipe to the point where it is invisible on most boards. Some woodworkers report zero snipe after setting their jointer correctly and using a snipe board. However, on very long or heavy boards, slight snipe may still appear if the board flexes during the pass.

Why does my jointer snipe only at the end of the board?

End snipe is almost always caused by the outfeed table being set too low. When the trailing end of the board leaves the infeed table, it drops onto the cutterhead because the outfeed table is not supporting it at the correct height. Raise the outfeed table until it is exactly level with the cutterhead’s highest point.

Does a spiral cutterhead prevent snipe?

No. A spiral cutterhead reduces tearout and noise, but snipe is a geometry issue related to table support. A spiral cutterhead can still produce snipe if the tables are misaligned or if you rock the board. The only way to prevent snipe is to ensure proper support and even pressure.

What is a snipe board and how do I use it?

A snipe board is a thin, flat piece of scrap wood that you attach to the top of your workpiece, extending beyond both ends. It gives the jointer tables extra surface to support, so the workpiece does not tip at the start or end of the pass. You can clamp it or use double-sided tape. The snipe board will get the dip instead of your workpiece.

Should I raise or lower the outfeed table to fix snipe?

You should raise the outfeed table if it is too low. The outfeed table must be exactly level with the cutterhead’s highest point. If it is too low, the board drops and the cutterhead cuts deeper at the end. If it is too high, the board will ride up and you will not get a flat cut. Use a straightedge to set it precisely.

Can I fix snipe by sanding it out?

You can sand out light snipe, but it is better to fix the cause. Sanding removes material and can make the edge uneven if you are not careful. For a glue joint, snipe must be removed entirely, or the joint will have a gap. Sanding is a temporary fix; adjusting the jointer is the permanent solution.

Related

How pages are sourced and corrected: Sources and editorial policy.