OneStopList

Gods and goddesses

Drilling with the Lathe: How to Do It Safely

Updated November 17, 2026

Yes, you can drill with a lathe, and it is a common operation in both woodturning and metalworking. The lathe holds the workpiece and spins it while a drill bit, mounted in the tailstock, is fed into the rotating material to create a centered hole. This article explains how it works, the tools you need, and the safety practices that keep the operation accurate and injury-free.

What Drilling on a Lathe Means

Drilling on a lathe is fundamentally different from drilling with a handheld drill or a drill press. In a drill press, the workpiece is stationary and the bit rotates. On a lathe, the workpiece rotates and the drill bit is held stationary (or turned slowly by hand) in the tailstock. This reversed setup allows you to drill holes that are perfectly concentric with the axis of rotation, which is essential for tasks like creating a center hole for a live center, boring out a bowl blank, or making a through-hole in a metal shaft.

The tailstock is the key component. It slides along the lathe bed and can be locked in position. It contains a quill (a sliding sleeve) that advances the drill bit into the work. The tailstock spindle usually has a Morse taper, which accepts a drill chuck or a drill bit with a matching taper shank. For most work, you will use a Jacob’s chuck (a three-jaw keyed chuck) held in the tailstock, which lets you use standard straight-shank drill bits.

How to Drill on a Lathe: Step-by-Step

Drilling on a lathe is straightforward once you understand the sequence. Here is a typical process for a woodturning or metalworking lathe:

  1. Mount the workpiece. Secure the blank in the chuck or between centers. For a bowl or a spindle, make sure it is running true (not wobbling).
  2. Install the drill bit. Insert the drill bit into a drill chuck mounted in the tailstock, or use a bit with a Morse taper shank directly in the tailstock spindle. Ensure the bit is tight.
  3. Align the tailstock. Slide the tailstock up to the workpiece until the drill bit is close to the surface. Lock the tailstock to the bed.
  4. Set the speed. Use a low speed—typically under 1,000 RPM for wood, and even lower (200–400 RPM) for metal. High speed creates heat and can break the bit.
  5. Advance the quill. Turn the tailstock handwheel to feed the bit into the rotating work. Apply steady, moderate pressure. For deep holes, withdraw the bit frequently to clear chips and prevent overheating.
  6. Retract and finish. Once the hole is the desired depth, back the bit out while the lathe is still running, then stop the lathe.

For deep holes (more than a few times the bit diameter), you may need to use a technique called peck drilling—advancing a small amount, retracting to clear chips, then advancing again. This is critical in metal to prevent the bit from jamming and breaking.

Choosing the Right Drill Bit and Speed

The drill bit you choose depends on the material and the hole size. For wood, standard high-speed steel (HSS) twist bits work fine, but a brad-point bit or a Forstner bit (if you have a chuck that can hold it) will give a cleaner entry and exit. For metal, use HSS or cobalt bits for steel, and carbide for hardened materials. For large holes in wood (like a bowl recess), you might use a Forstner bit held in the tailstock, but be careful: large bits require very low speed and light feed to avoid grabbing.

Speed is critical. A general rule for twist drills is to run at a surface speed of about 100–200 feet per minute for wood and 50–100 for mild steel. To calculate RPM, use the formula: RPM = (4 x cutting speed in feet per minute) / diameter of the bit in inches. So for a 1/2-inch bit in wood (cutting speed ~200), the RPM would be (4 x 200) / 0.5 = 1600 RPM. For a 1/2-inch bit in steel (cutting speed ~100), it would be 800 RPM. Many turners simply use the lowest speed that still cuts cleanly, especially for larger bits.

Common Problems and How to Avoid Them

Drilling on a lathe can go wrong in a few predictable ways. The most common is the drill bit wandering off-center. This happens when the bit enters the workpiece at an angle or when the workpiece has a hard grain. To prevent this, start with a center drill (a short, stiff bit) to create a pilot hole. For metal, center drilling is essential. Another issue is the bit grabbing the wood and pulling itself in violently, which can split the wood or break the bit. This is often caused by too high a speed or too aggressive a feed. Always use a slow speed and steady, even pressure.

Heat is another enemy. If the bit gets too hot, it will lose its temper and become dull. Use cutting fluid for metal (or even a little oil) and withdraw the bit frequently to allow air to cool it. For wood, a sharp bit and moderate speed usually prevent burning. Finally, the tailstock can slip if it is not locked properly. Always make sure the tailstock is clamped to the bed before drilling.

Drilling on a Metal Lathe vs. Wood Lathe

The basic principle is the same, but there are differences. On a metal lathe, you have a carriage and compound rest, and the tailstock is often used with a drill chuck or a center. You can also mount a drill bit in the tool post and feed the work into it, but that is less common. Metal lathes require cutting fluid, lower speeds, and rigid setup to avoid chatter. Wood lathes are more forgiving, but you must be careful of tear-out at the exit hole. To prevent splintering on the back side of a wood piece, drill from both ends or back up the exit with a scrap block.

Another difference is the use of a live center. When drilling between centers, you often need to drill a center hole first to support the work. On a metal lathe, you use a center drill to create a 60-degree countersink that matches the live center. On a wood lathe, you might use a spur center or a cup center, and you may not need a pilot hole if the bit is guided by the tailstock.

Safety Considerations

Safety is paramount when drilling on a lathe. The rotating workpiece can catch loose clothing, hair, or jewelry, so always tie back long hair, remove jewelry, and wear a snug-fitting apron or shop coat. Wear safety glasses or a face shield to protect against flying chips and broken bits. Never attempt to clear chips with your hand while the lathe is spinning—stop the lathe first. Also, be aware of the drill bit’s length: if you are drilling a through-hole, the bit will exit the back of the workpiece and could hit the tailstock if it is too long. Always leave enough clearance.

For metal, use cutting fluid to reduce heat and improve chip flow. For wood, be cautious of the bit grabbing and causing a catch. If you feel excessive vibration or hear a squealing sound, stop and check the setup. Never force the feed; let the bit cut at its own pace.

Alternatives to Tailstock Drilling

Sometimes you need to drill a hole that is not on the centerline. In that case, you can use a drill press or a handheld drill after turning. But if you need a hole that is perfectly centered, the lathe is the best tool. Another alternative for large holes in wood is to use a hollow auger or a Forstner bit in the tailstock, but these require very low speed and a firm grip. For metal, you can use a boring bar to enlarge an existing hole—this is done with the cutting tool mounted on the carriage, not the tailstock. Boring allows you to achieve precise diameters and a good surface finish.

For very deep holes (like a gun barrel), you would need a specialized gun drill or a deep-hole drilling setup, which is beyond the scope of a standard lathe. But for most workshop tasks, tailstock drilling is sufficient.

Frequently Asked Questions

Can I use a regular drill bit on a lathe?

Yes, you can use a standard twist drill bit, but it must be held securely in a drill chuck in the tailstock. For wood, a brad-point bit gives a cleaner hole. For metal, use a sharp HSS bit and cutting fluid. Just make sure the bit is straight and not bent.

Why does my drill bit wander off-center?

Wandering is usually caused by starting the hole on an uneven surface or using a dull bit. Use a center drill first to create a pilot hole. Also, make sure the tailstock is aligned with the headstock—if it is off by even a fraction, the hole will be off-center.

What speed should I use for drilling on a lathe?

Use a low speed—generally under 1,000 RPM for wood and under 500 RPM for metal. The exact speed depends on the bit diameter and material. As a rule, the larger the bit, the slower the speed. If you see smoke or the bit turns blue, you are going too fast.

Do I need cutting fluid for wood?

No, cutting fluid is for metal. For wood, a sharp bit and moderate speed will prevent burning. If you are drilling a lot of holes, you can use a wax stick to lubricate the bit, but it is not necessary.

How do I drill a deep hole without the bit breaking?

Use peck drilling: advance a small amount (about half the bit diameter), retract to clear chips, then advance again. This prevents chips from clogging the flutes, which causes heat and breakage. Also, use a slow speed and steady pressure.

Can I drill a hole in a spinning workpiece without a tailstock?

No, you should never attempt to hold a drill bit by hand against a spinning workpiece. The bit will catch and could cause serious injury. Always use the tailstock to hold the bit securely.

Related

How pages are sourced and corrected: Sources and editorial policy.