OneStopList

Gods and goddesses

DMT Sharpener Kit for Turners & Carvers: Full Guide

Updated November 18, 2026

A DMT sharpener kit for turners and carvers is a set of diamond-coated sharpening stones, typically including a fine or extra-fine bench stone, a coarse stone, and often a leather strop or honing compound, designed to maintain the edge on woodturning gouges, scrapers, and carving tools. These kits are popular because diamond abrasive sharpens hardened tool steel quickly and flatly without requiring oil, and the stones never need flattening themselves.

Why Turners and Carvers Choose Diamond Kits

Woodturners and carvers work with tools that need frequent sharpening. Traditional oil stones and water stones work, but they require maintenance and can be messy. Diamond stones, like those from DMT (Diamond Machining Technology), use a thin layer of industrial diamond particles bonded to a flat steel plate. This gives several practical benefits in a workshop:

  • Speed: Diamond is harder than any tool steel, so it cuts fast, especially on high-speed steels like M2 and powder metals.
  • Flatness: The steel plate stays flat, so you can sharpen flat bevels and skewed tools accurately.
  • No oil or water needed: You can use them dry or with a light spray of water or honing oil. Many turners use them dry for convenience.
  • Durability: A quality diamond stone lasts for years with normal use, though the diamond layer does wear eventually.

For turners, the most common tools are bowl gouges, spindle gouges, and scrapers. Carvers use chisels, gouges, and V-tools. A kit that includes a coarse stone (around 220–325 grit) for reshaping and a fine or extra-fine stone (around 600–1200 grit) for honing covers most needs.

What’s Typically in a DMT Sharpener Kit

DMT offers several kits. A common one is the “Dia-Sharp” kit, which includes a coarse (325 grit) and fine (600 grit) stone, plus a leather strop with polishing compound. Another is the “DuoSharp” kit, which has a bench stone with two grits (one on each side) and a base. Some kits include a “Dia-Flat” plate for flattening water stones, but that’s more for carvers who use water stones. For turners, a typical kit might include:

  • Coarse diamond stone (e.g., 220 or 325 grit) for grinding and reshaping.
  • Fine diamond stone (e.g., 600 grit) for sharpening.
  • Extra-fine diamond stone (e.g., 1200 grit) for polishing.
  • Leather strop with chromium oxide compound for a final edge.

Some kits are specifically marketed as “turner’s kits” and include a flat stone and a cone-shaped or tapered stone for sharpening the inside of gouges. DMT’s “Sharpening Kit for Turners” includes a 6-inch diamond stone and a cone-shaped diamond file. Carvers might prefer a kit with smaller stones or a set of diamond paddles (small, thin stones) for detail work.

How to Use a Diamond Stone for Turning Tools

Sharpening a bowl gouge on a flat diamond stone requires a consistent technique. Here’s a basic method for a fingernail-style bowl gouge:

  1. Lay the gouge on the stone with the bevel flat against the diamond surface.
  2. Roll the gouge from one side to the other while moving it back and forth along the stone, maintaining the same angle.
  3. Use a light touch—let the diamond do the work. Pressing hard only wears the stone faster.
  4. After a few passes, check the edge for a burr (a thin wire edge) on the inside of the flute. When you feel a consistent burr, the edge is sharp.
  5. Remove the burr by lightly honing the inside of the flute with a small diamond cone or a slip stone, then strop.

For scrapers, you simply lay the flat bevel on the stone and move it back and forth. For carving chisels, hold the bevel flat and slide the tool across the stone with a circular or back-and-forth motion.

Choosing the Right Grit and Kit

The grit you need depends on the condition of your tools and your preference for edge finish. A coarse stone (220–325) is for reshaping or repairing nicks. A fine stone (600) is for everyday sharpening. An extra-fine stone (1200) gives a polished edge that many turners prefer for a clean cut on end grain. A strop with compound can take the edge even further, but some turners skip it because a 1200-grit diamond edge is already very sharp.

When choosing a kit, consider:

  • Stone size: For turning tools, a 6-inch or 8-inch long stone is easier to use for long sweeps. For carving, a 4-inch or 6-inch stone is fine.
  • Portability: If you travel to demos or classes, a smaller kit or a set of diamond paddles is easier to carry.
  • Base: Some stones come with a non-slip rubber base, which is helpful. You can also use a damp paper towel under the stone to keep it from sliding.
  • Grit range: A kit with coarse and fine is enough. Adding extra-fine is nice but not essential.

Common Mistakes and Misconceptions

One common misconception is that diamond stones don’t need any preparation. That’s true—they don’t need flattening, but they do need cleaning. Metal particles and swarf clog the diamond surface. You can clean them with a little dish soap and water, or a commercial stone cleaner. Some people use a rubber eraser to clean the stone, but that’s less effective.

Another mistake is using too much pressure. Diamond stones cut fast, but pressing hard can dislodge the diamond particles. Use a light touch and let the stone do the work.

Also, some turners think that a strop is only for straight edges. In fact, you can strop curved gouges by using a leather wheel or a flat strop with a curved motion. But if you don’t have a strop, a fine diamond stone is enough.

Finally, note that diamond stones do wear out eventually. If you use them heavily, the diamond layer may wear thin after several years. But for most hobbyists, a good diamond stone lasts a very long time.

DMT vs. Other Sharpening Systems

DMT is not the only option. Other diamond stone brands include Trend, Atoma, and EZE-Lap. Atoma stones are popular because they have a replaceable diamond film, but they are more expensive. DMT stones are well-regarded for their consistency and reasonable price.

Compared to water stones, diamond stones are more convenient and don’t need soaking. Compared to bench grinders, diamond stones are quieter and don’t remove metal as fast, but they give a more precise edge. Many turners use a grinder for shaping and a diamond stone for sharpening.

For carvers, a set of diamond paddles (small, thin stones) is often more versatile than a bench stone because they can get into tight spaces. DMT makes a “Dia-Pad” set that includes several small stones with different grits.

Cost and Value

A DMT sharpener kit typically costs between $50 and $150, depending on the size and number of stones. A basic Dia-Sharp kit with two stones and a strop is around $80–$100. A larger kit with extra-fine stone and a base might be $120–$150. That’s comparable to a good set of water stones, but diamond stones last longer and require less maintenance.

For a beginner, a simple kit with a coarse and fine stone is enough. As you get more experienced, you might add an extra-fine stone or a strop. The value is in the longevity and convenience.

Safety and Maintenance

Sharpening is safe if you follow basic precautions:

  • Always keep your fingers behind the cutting edge.
  • Use a light touch to avoid overheating the tool (diamond stones don’t generate much heat, but grinding does).
  • Wear safety glasses in case a chip flies off.
  • Clean the stone after each use to prevent metal particles from rusting the tool steel.

To clean a diamond stone, rinse it under water and scrub with a nylon brush or an old toothbrush. You can use a mild detergent. Dry it with a cloth. Do not use harsh chemicals or put it in the dishwasher.

Store the stones in a dry place, preferably in a protective case or with a cover to prevent damage to the diamond surface.

Frequently Asked Questions

Can I use a DMT diamond stone on carbide tools? Yes, you can. Carbide is harder than steel, but diamond is harder than carbide, so it will sharpen them. However, carbide tools are often not meant to be sharpened—they have replaceable tips. If you do sharpen them, use a fine or extra-fine diamond stone and a light touch.

Do I need to use oil or water with DMT stones? No. You can use them dry. Some people use a light spray of water or honing oil to float the swarf, but it’s not necessary. If you use oil, clean the stone afterward with soap and water.

How do I sharpen a bowl gouge with a DMT stone? Lay the bevel flat on the stone and roll the gouge from side to side while moving it back and forth. Keep the same angle and use a light touch. Check for a burr on the inside of the flute, then remove it with a cone-shaped diamond file or a slip stone.

What grit should I use for carving tools? For carving, a fine (600) or extra-fine (1200) stone is usually enough. If your tools are very dull or have nicks, start with a coarse (325) stone to reshape, then move to fine.

Can I use a DMT stone to flatten water stones? Yes, but you need a special plate like the DMT Dia-Flat, which is a coarse diamond plate designed for that purpose. A regular bench stone might work, but it will wear faster and may not be flat enough.

How long do DMT stones last? With normal use and proper care, a DMT diamond stone can last for many years. The diamond layer will eventually wear, but it’s not uncommon for a stone to last a decade or more for a hobbyist.

Related

How pages are sourced and corrected: Sources and editorial policy.