OneStopList

Gods and goddesses

Ares Ham Radio Frequencies: Complete Guide

Updated November 21, 2026

Ares ham radio frequencies are not a single, fixed set of channels; the term “Ares” refers to the Amateur Radio Emergency Service, a program of the American Radio Relay League (ARRL) that uses standard amateur bands plus locally designated repeater and simplex frequencies. These frequencies vary by region, so there is no universal “Ares channel” you can dial in—instead, you must look up the specific frequencies for your local ARES unit.

What Is ARES and Why Does It Use Frequencies?

The Amateur Radio Emergency Service (ARES) is a volunteer organization of licensed amateur radio operators who provide emergency and public-service communications during disasters, severe weather, or community events. ARES is sponsored by the ARRL and operates under the Federal Communications Commission (FCC) rules for amateur radio in the United States. Because amateur radio operators are licensed to use specific frequency bands, ARES does not own exclusive frequencies; it uses the same VHF/UHF and HF bands available to all hams, but coordinates its members to monitor designated channels during activations.

Typical ARES operations rely on local repeater frequencies (often 2-meter, 144–148 MHz) because they give good coverage over a city or county. Some groups also use 70-centimeter (420–450 MHz) repeaters, and for longer distances or when repeaters fail, they use HF bands (e.g., 80, 40, or 20 meters) for regional or statewide nets.

How to Find Your Local ARES Frequencies

Because frequencies are local, the first step is to contact your county or state ARES organization. The ARRL maintains a directory of ARES groups by state, and each group typically publishes its frequencies on its website or in its training materials. You can also find them through:

  • Your local amateur radio club’s website or newsletter
  • The ARRL’s “ARES” page, which lists state and section emergency coordinators
  • Repeater directories like RepeaterBook or the ARRL Repeater Directory, searching for repeaters with an “ARES” or “RACES” note
  • Listening during a weekly net—most ARES groups hold a regular on-air net (e.g., every Monday at 7 PM) and announce the frequency at the start

Do not assume a frequency from another state will work. For example, a repeater in Ohio will not be accessible from California, and even within a state, different counties may use different repeaters.

Common ARES Frequency Bands and Modes

While exact frequencies vary, ARES operations commonly use these bands and modes:

  • 2-meter VHF (144–148 MHz): The backbone for local communications. FM voice is the most common mode, and repeaters are widely used.
  • 70-centimeter UHF (420–450 MHz): Often paired with 2-meter for local nets; better in urban areas with buildings but shorter range.
  • HF (1.8–30 MHz): Used for statewide or regional nets, especially on 40 meters (7.0–7.3 MHz) and 80 meters (3.5–4.0 MHz) during emergencies when repeaters are down.
  • Digital modes: Some groups use DMR, D-STAR, or Fusion digital voice, but analog FM remains the most common because it is universally compatible.

For example, a typical ARES net might meet on a 2-meter repeater with a frequency of 146.880 MHz and a negative offset of 600 kHz, using a PL tone of 110.9 Hz. That exact combination is local, not national.

ARES vs. RACES: Frequencies and Differences

ARES is often confused with RACES (Radio Amateur Civil Emergency Service), which is a separate program activated by government agencies during declared emergencies. The key differences are:

  • ARES is voluntary and can be activated by any ARES group for any public-service event, not just declared disasters.
  • RACES is activated only by a government official (e.g., a county emergency manager) during a declared emergency, and it restricts communications to official emergency traffic.
  • Frequencies are not exclusive to either; both use the same amateur bands. However, RACES may have specific pre-arranged frequencies with local emergency management offices.

Many hams belong to both groups and share the same repeaters, but the rules about who can transmit and when differ.

How to Choose the Right Radio for ARES Frequencies

To participate in ARES on the most common frequencies, you need a radio that can transmit on 2 meters and 70 centimeters. A dual-band handheld (HT) like a Yaesu FT-60R or a Baofeng UV-5R is sufficient for local nets and most activations. For better coverage, a mobile radio with a high-gain antenna is recommended. If you plan to work HF nets, you need a separate HF transceiver and a license class that allows HF (General or Amateur Extra).

When choosing a radio, consider:

  • Does it support the PL tones used by your local repeaters? Most modern radios do.
  • Is it capable of transmitting on 2m and 70cm? Yes, if it is dual-band.
  • Can it operate on battery power for emergencies? A handheld with a spare battery is ideal.
  • Does it have a standard SMA or BNC antenna connector for easy replacement?

Remember that transmitting on any frequency requires a valid amateur radio license; you cannot use a scanner or a GMRS radio for ARES.

Common Problems with ARES Frequencies and Solutions

Newcomers often encounter a few recurring issues:

  • PL tone mismatch: If you can hear the repeater but cannot transmit, you may have the wrong tone or no tone set. Check the repeater’s listing for the correct CTCSS tone.
  • Offset error: On 2 meters, the standard offset is 600 kHz (usually negative for repeaters above 147 MHz). If your radio is set to simplex, you will not key the repeater.
  • Repeater coverage gaps: During an emergency, a repeater may be overloaded or off the air. ARES groups often identify a simplex frequency (e.g., 146.520 MHz) as a fallback—this is a national calling frequency, not an ARES exclusive.
  • Out-of-date frequency lists: Repeaters change tones or frequencies. Always verify with a current directory or by listening to the net before an activation.

If you cannot reach a repeater, try raising your antenna, moving to a higher location, or using a mobile radio with more power.

Costs and Licensing for ARES Participation

Joining ARES is free, but you must have an amateur radio license. The FCC license costs $35 and is valid for ten years. A basic dual-band handheld can cost as little as $30–$80, while a quality mobile radio ranges from $150–$400. HF equipment is more expensive, starting around $500 for a used transceiver. Many ARES groups offer free training and will help you program your radio. You do not need to buy expensive gear to start; a simple HT is enough to check into a local net.

Safety and Best Practices for ARES Frequencies

Operating on ARES frequencies is safe if you follow standard amateur radio practices:

  • Always identify with your call sign at the end of a transmission and every 10 minutes during a long transmission.
  • Do not transmit on a repeater without listening first; wait for a pause in traffic.
  • During an actual emergency, follow the net control station’s instructions—do not break in unless you have urgent traffic.
  • Keep your radio’s battery charged and have a backup power source (e.g., a car battery or solar panel) for extended activations.
  • Never transmit on frequencies outside your license privileges or on non-amateur bands.

ARES is not a hobby for unlicensed listeners; it is a licensed service, so you must pass a basic exam to participate.

Frequently Asked Questions

What is the national ARES frequency?

There is no national ARES frequency. The ARRL does not assign a single channel; instead, each local group chooses its own repeaters and simplex frequencies. The national calling frequency for 2 meters is 146.520 MHz, but it is not an ARES net frequency—it is just a place to make initial contact.

Can I listen to ARES frequencies without a license?

Yes, you can listen to any amateur radio frequency with a scanner or a receiver without a license. However, you cannot transmit unless you have an FCC amateur radio license. Listening is a great way to learn how nets operate before you get licensed.

Do ARES frequencies change during an emergency?

Sometimes. If a primary repeater fails or is overloaded, the net control may announce a backup frequency. Many ARES groups pre-plan a simplex frequency and a secondary repeater for this purpose. Always monitor the primary net until you are told otherwise.

Are ARES frequencies the same as RACES frequencies?

Not necessarily. ARES and RACES often share the same repeaters, but RACES may have additional frequencies coordinated with local emergency management. During a RACES activation, only RACES members may transmit on those specific frequencies, even if they are also ARES members.

What is the best radio for a beginner in ARES?

A dual-band handheld (2m/70cm) is the best starting point. Popular models include the Yaesu FT-60R, the Icom ID-52A, or a budget Baofeng UV-5R. Look for one that supports CTCSS tones and has a long battery life. You can upgrade to a mobile or HF radio later as you gain experience.

Related

How pages are sourced and corrected: Sources and editorial policy.