To replace the battery in an Apollo oil tank monitor, you must open the transmitter unit and swap the old battery for a new one, typically a 3V lithium cell such as a CR123A or CR2, depending on your exact model. The process takes about five minutes and requires only a small Phillips-head screwdriver, but you must follow the specific steps below to avoid damaging the unit or losing your calibration.
Understanding Your Apollo Oil Tank Monitor
Apollo is a well-known brand in the UK and Ireland for home heating oil tank monitoring. Their systems consist of a sensor that sits inside or on top of your oil tank, a transmitter that sends the level data wirelessly, and a receiver display unit inside your home. The transmitter is the part that contains the battery you need to replace. There are several models in the Apollo range, including the standard Apollo transmitter (often paired with the Apollo Receiver) and the newer Apollo Smart units that connect to a smartphone app. The battery type and replacement procedure can vary slightly between these generations, so always check your model number before buying a replacement.
What Battery Does the Apollo Transmitter Use?
Most Apollo oil tank monitor transmitters use a 3V lithium battery. The most common types are:
- CR123A – used in many of the standard Apollo transmitters (e.g., the ones paired with the Apollo Receiver).
- CR2 – used in some newer or compact models.
- AA or AAA lithium – a few older or specific models may use these, but they are less common.
To be certain, open the transmitter’s battery compartment and read the label on the old battery. It will clearly state the type (e.g., “CR123A 3V”). If the label is worn, check the user manual or the Apollo website for your specific model. Using the wrong battery can damage the transmitter or cause it to malfunction.
Step-by-Step Battery Replacement
- Power down the receiver: If you have a receiver display, press the reset or power button to turn it off. This prevents the system from trying to communicate with the transmitter while you work.
- Locate the transmitter: It is usually attached to the top of your oil tank or mounted on a nearby wall, connected to the sensor by a short cable.
- Open the case: Use a small Phillips-head screwdriver to remove the screws on the transmitter’s lid. Some models have a clip or a twist-lock instead. Be gentle – the plastic can be brittle after years of outdoor exposure.
- Remove the old battery: Note the orientation (+ and -) before you take it out. Use a plastic tool or your fingernail to lift the battery out. Do not use a metal screwdriver to pry it out – you could short-circuit the contacts.
- Insert the new battery: Place the new battery in the same orientation. Press it down firmly until it clicks into place.
- Close and reseal the case: Replace the lid and tighten the screws. Make sure the rubber gasket (if any) is seated properly to keep out moisture.
- Re-power the receiver: Turn the receiver back on. It should automatically re-sync with the transmitter within a few minutes. If not, press the “pair” or “test” button on the transmitter (if available) or follow the manual’s instructions.
How Often Should You Replace the Battery?
Apollo states that the transmitter battery typically lasts between 12 and 24 months, depending on the model and how often the transmitter sends signals. If your tank monitor starts showing a low-battery warning on the receiver, or if the level readings become erratic or stop updating, it’s time to replace the battery. It’s a good idea to replace it proactively every 18 months, especially before winter when you rely on the monitor most. Some users report batteries lasting longer (up to 3 years) if the tank is checked infrequently, but that’s not the norm.
Common Problems and Troubleshooting
After replacing the battery, you might encounter a few issues:
- No signal: If the receiver still shows “no signal,” check that the battery is fully seated and the case is closed properly. You may also need to re-pair the transmitter and receiver – usually done by holding the “test” button on the transmitter for 5 seconds.
- Erratic readings: This can happen if the battery contacts are dirty or corroded. Clean them gently with a dry cloth or a pencil eraser. Also, ensure the sensor wire is still connected firmly.
- Water inside the case: If you see moisture, dry it out completely before inserting a new battery. The rubber gasket may need replacing – you can get a new one from Apollo.
- Battery drains quickly: If a new battery dies within a month, there may be a short circuit or the transmitter may be faulty. Contact Apollo support or your installer.
Costs and Where to Buy Replacement Batteries
A CR123A or CR2 lithium battery costs roughly £3–£6 at a hardware store, electronics shop, or online. You can also buy them in multi-packs. Make sure you buy a reputable brand (e.g., Duracell, Energizer, Panasonic) – cheap unbranded batteries may not last as long or may leak. If you prefer a one-stop solution, some suppliers sell “Apollo battery replacement kits” that include the correct battery and a small screwdriver. These kits are often available on Amazon or from heating oil suppliers. Avoid buying from unknown sellers on marketplaces if you’re concerned about counterfeits.
Safety and Disposal
Lithium batteries are safe when handled correctly, but they must be disposed of properly – never throw them in household waste. In the UK and Ireland, you can take them to a local recycling centre or a shop that sells batteries. Do not incinerate lithium batteries, and do not leave them exposed to high heat. When handling the battery, avoid touching both terminals with metal objects, and do not attempt to recharge a non-rechargeable lithium battery – it can explode. If the battery leaks, wear gloves and clean the compartment with a dry cloth, then dispose of the battery safely.
Alternatives to DIY Replacement
If you’re not comfortable working with the transmitter, or if your monitor is still under warranty, you can contact the installer or Apollo’s customer service. They may replace the battery for a small fee, or you can purchase a new transmitter unit if the old one is faulty. Some heating oil delivery companies offer a service where they check your tank monitor during routine deliveries. However, for most people, DIY replacement is straightforward and safe – just follow the steps above.
Frequently Asked Questions
How do I know when the battery is low?
Your receiver will show a “low battery” icon or a warning message. Some models also beep. If you don’t see that, but the readings stop updating, check the battery.
Can I use a rechargeable battery?
No. Apollo transmitters are designed for non-rechargeable 3V lithium batteries. Rechargeable batteries have lower voltage (usually 3.6V or 1.2V per cell) and may not power the transmitter correctly or could damage it.
Will I lose my tank level reading when I change the battery?
No, the sensor itself has a float that measures the level, and the transmitter will send the current level to the receiver once it re-syncs. You don’t need to recalibrate anything.
My transmitter is outdoors – do I need to worry about weather?
Yes, the transmitter is weatherproof, but when you open it, make sure the inside is dry. If it’s raining, do the replacement indoors or under cover.
What if the battery is glued in?
Some models have a battery holder with a clip, but if yours is glued, gently pry it loose with a flat-head screwdriver – but be careful not to damage the circuit board. If it’s very stuck, contact Apollo.
Related
- All Fish for Poseidon Rod? Full List & Guide
- All of Hades’ Kids: Full List of Children
- Hades Greek Mythology Personality: God of the Underworld
How pages are sourced and corrected: Sources and editorial policy.