Steel yield strength is the amount of stress at which steel begins to deform permanently, meaning it will not return to its original shape when the load is removed. For most structural steels, this value ranges from 36,000 to 100,000 psi (250 to 690 MPa), but specific grades can go much higher.
What Exactly Is Yield Strength?
When you pull on a piece of steel, it first stretches elastically—like a rubber band—and returns to its original length when you let go. If you keep pulling, you eventually reach the yield point, where the steel starts to flow plastically. Beyond that point, even after you remove the load, the steel stays stretched. That permanent deformation is the yield, and the stress at which it starts is the yield strength.
Engineers design most steel structures so that the stress never exceeds the yield strength under normal working loads. This ensures that a bridge or building won’t permanently bend or sag after a heavy truck passes or a strong wind blows. The yield strength is also the basis for calculating allowable stress in many design codes, often with a safety factor applied.
How Yield Strength Is Measured
The standard test is the tensile test, described in ASTM E8 (in the US) and ISO 6892 (internationally). A machined sample of steel is pulled in a testing machine while a strain gauge records how much it stretches. The result is plotted on a stress-strain curve.
- Elastic region: The curve is a straight line (Hooke’s law). The slope is the modulus of elasticity, about 29,000 ksi (200 GPa) for all steels.
- Yield point: For low-carbon steel, there is a distinct “yield plateau” where the stress drops slightly and then fluctuates—this is the upper and lower yield point. The lower yield point is usually taken as the yield strength.
- For high-strength steels: There may be no clear plateau, so the yield strength is defined as the stress at 0.2% offset strain. That means you draw a line parallel to the elastic slope starting at 0.2% strain; where it crosses the curve is the yield strength.
The test is done at room temperature unless you specifically need elevated-temperature properties. Yield strength decreases as temperature rises, which is why steel loses strength in a fire.
Common Steel Grades and Their Yield Strengths
Steel is categorized by grades, each with a specified minimum yield strength. Here are some widely used ones:
- A36 (structural carbon steel): Minimum yield 36,000 psi (250 MPa). Used for general structures, beams, and plates.
- Grade 50 (ASTM A992): Minimum yield 50,000 psi (345 MPa). The most common for wide-flange structural beams in the US.
- Grade 60 rebar (ASTM A615): Minimum yield 60,000 psi (420 MPa). Used in reinforced concrete.
- High-strength low-alloy (HSLA) steels: Yield from 50,000 to 80,000 psi (345–550 MPa). They add small amounts of vanadium or niobium for strength without much extra cost.
- Quenched and tempered steels (e.g., ASTM A514): Yield up to 100,000 psi (690 MPa). Used in cranes and heavy equipment.
- Maraging steels: Yield can exceed 280,000 psi (1,930 MPa), but they are expensive and used in aerospace and tooling.
Remember that the listed yield is a minimum; actual tested values are usually higher. Also, the yield strength of a steel can be increased by cold working (like bending or drawing), but this reduces ductility.
Yield Strength vs. Tensile Strength
People often confuse yield strength with tensile strength, but they are different. Tensile strength (or ultimate tensile strength) is the maximum stress the steel can withstand before it fractures. For structural steels, tensile strength is typically 1.5 to 2 times the yield strength. For example, A36 has a tensile strength of 58,000–80,000 psi, while its yield is 36,000 psi.
The ratio of yield to tensile strength is called the yield-to-tensile ratio. A lower ratio (like 0.6) means the steel will deform a lot before breaking, giving warning. A higher ratio (like 0.9) means the steel is strong but may fracture suddenly. Design codes often limit this ratio for seismic applications.
Factors That Affect Yield Strength
Several things change a steel’s yield strength:
- Chemical composition: Carbon, manganese, and other alloying elements increase strength. More carbon makes steel harder but less ductile and harder to weld.
- Heat treatment: Quenching and tempering can dramatically raise yield strength. Annealing softens steel and lowers yield strength.
- Cold working: Bending, rolling, or drawing at room temperature increases yield strength through strain hardening.
- Grain size: Finer grains give higher yield strength (Hall-Petch effect). This is why thermomechanical processing often improves strength.
- Temperature: Yield strength drops at high temperatures and rises at low temperatures. At very low temperatures, some steels become brittle.
For design, you always use the specified minimum yield strength, not the maximum, because you want the steel to perform at least as well as expected.
How to Choose the Right Yield Strength
Selecting a steel grade involves balancing strength, cost, weldability, and ductility. Here are some guidelines:
- Determine the required strength: Calculate the maximum stress the part will see under load. Apply a safety factor (typically 1.5 to 2 for static loads) to get the required minimum yield strength.
- Consider fabrication: Higher strength steels often require preheating before welding and special electrodes. If you need to bend or form the steel, a lower strength grade may be easier.
- Check ductility: For applications that absorb energy (like earthquake-resistant frames), you want a steel with good elongation, not just high yield. Look for a minimum elongation of 20% or more.
- Evaluate cost: Higher yield strength usually means higher cost per pound, but you may use less material. Compare total cost, not just material cost.
- Look at availability: Common grades like A36 or A992 are readily available. Exotic high-strength steels may need to be ordered with long lead times.
For example, a simple warehouse column might use A992 (50 ksi yield) because it’s economical and weldable. A crane boom might use A514 (100 ksi yield) to reduce weight, even though it costs more and needs careful welding.
Common Misconceptions
One myth is that “higher yield strength always means better.” Not true—high-strength steels are often less ductile and more sensitive to notches. A sudden impact or a sharp corner can cause brittle fracture. That’s why many codes require a minimum toughness, not just strength.
Another misconception is that yield strength is the same as the stress at which a steel part fails. Actually, failure can occur at a lower stress if the part has a crack or defect, or at a higher stress if the load is applied very quickly (strain rate effect). Yield strength is a material property, but real-world failures depend on geometry, loading, and environment.
Also, stainless steel is not always stronger than carbon steel. Some stainless grades have yield strengths as low as 30,000 psi, while many carbon steels are stronger. The “stainless” refers to corrosion resistance, not strength.
Frequently Asked Questions
What is the yield strength of mild steel?
Mild steel (low-carbon steel) typically has a yield strength of about 36,000 psi (250 MPa). That’s the minimum for A36, the most common mild steel grade. Some mild steels may have a slightly higher yield, but 36 ksi is the standard design value.
How do I find the yield strength of a steel sample?
You need to perform a tensile test on a standardized specimen. If you don’t have a lab, you can identify the grade from markings or mill certificates and look up its specified minimum yield strength. For rebar, the grade number (e.g., 60) indicates the yield in ksi.
Is yield strength the same as breaking strength?
No. Breaking strength (tensile strength) is the maximum stress before fracture, which is higher than yield strength. For example, A36 has a yield of 36 ksi and a tensile strength of 58–80 ksi. The steel will permanently deform well before it breaks.
Can you increase the yield strength of steel by heat treatment?
Yes, but only for steels that are hardenable, like medium-carbon or alloy steels. Quenching and tempering can raise yield strength significantly. Low-carbon steels like A36 don’t respond much to heat treatment; you’d need cold working or alloying instead.
Why does yield strength matter in earthquake design?
In seismic design, engineers want steel to yield in a controlled manner to absorb energy without fracturing. That means they need a known yield strength and good ductility. Using a steel with too high a yield might make the structure too stiff and brittle, so codes often limit the yield-to-tensile ratio and require minimum elongation.
Related
- Lakes Foot and Ankle Commerce MI: What to Know
- Lakes Gas Wisconsin: Real or Myth?
- Lakes Edge Apartments Sanford FL: Full Guide
How pages are sourced and corrected: Sources and editorial policy.