OneStopList

Gods and goddesses

A36 Yield Strength: Facts & Uses

Updated November 17, 2026

A36 steel’s minimum yield strength is 36,000 psi (250 MPa), which is where its name comes from. This article explains what that number means in practice, how it compares to other common steels, and what to consider when using A36 in real projects.

What Is A36 Steel?

A36 is a low-carbon steel plate, sheet, and bar product defined by the ASTM A36/A36M standard. It is one of the most widely used structural steels in the United States because it is inexpensive, weldable, and available in a wide range of shapes. The “36” in its name refers to its minimum yield strength of 36,000 pounds per square inch (psi), or 250 megapascals (MPa) in metric units.

The standard was first issued in the 1960s and has been revised many times. It covers carbon steel shapes, plates, and bars of structural quality. The chemical composition is not fixed; it allows for small amounts of manganese, copper, and other elements, as long as the mechanical properties meet the minimums.

Yield Strength vs. Tensile Strength

Yield strength is the stress at which a material begins to deform plastically. If you pull a steel bar and it stretches but returns to its original length when you release the force, you are below the yield point. Once you exceed yield strength, the bar stays permanently stretched even after the load is removed. For A36, that permanent deformation starts at 36,000 psi.

Tensile strength (also called ultimate tensile strength) is the maximum stress a material can withstand before it fractures. A36 has a tensile strength range of 58,000–80,000 psi (400–550 MPa). So there is a significant gap between when A36 starts to yield and when it actually breaks. This gives a warning before failure—a beam will visibly bend before it snaps.

In practical terms, design codes like AISC (American Institute of Steel Construction) use yield strength for allowable stress calculations, not tensile strength. That is why the 36,000 psi number matters more than the higher tensile value.

How A36 Compares to Other Steels

Several other structural steels are common competitors to A36. Here is a quick comparison based on typical published minimum values:

  • A572 Grade 50: yield strength 50,000 psi (345 MPa). Stronger than A36, often used for bridges and heavy structures, but slightly more expensive.
  • A992: yield strength 50,000–65,000 psi (345–450 MPa). This is the standard for wide-flange structural shapes (I-beams) in the US, replacing A36 for most new building frames.
  • 1018 steel: a cold-rolled carbon steel with yield strength around 54,000 psi (370 MPa) in the cold-drawn condition. Used for shafts and machined parts, not structural members.
  • Stainless steel 304: yield strength about 30,000 psi (205 MPa) in annealed condition. Lower than A36, but corrosion-resistant.

For most building frames, A992 or A572 are now preferred because they allow smaller members that still meet strength requirements. A36 remains popular for plates, angles, and channels, and for projects where welding is critical because its low carbon content makes it very weldable.

Common Uses of A36

Because of its balanced properties and low cost, A36 appears in many everyday structures:

  • Building frames (though often replaced by A992 for wide-flange sections)
  • Bridge components
  • Industrial platforms and walkways
  • Truck frames and trailers
  • Agricultural equipment
  • General fabrication, such as brackets, bases, and supports
  • Art and architectural sculptures

It is not suitable for applications requiring high hardness (like cutting tools) or high wear resistance. It also lacks corrosion resistance, so it must be painted or galvanized for outdoor use.

Factors That Affect Actual Yield Strength

The 36,000 psi figure is a minimum. Real A36 often has a higher yield strength, sometimes 40,000–45,000 psi, depending on the mill and the thickness. Several factors influence the actual value:

  • Thickness: Thicker plates (over 8 inches) may have slightly lower yield strength because the cooling rate during rolling is slower, leading to a coarser grain structure.
  • Heat treatment: A36 is normally supplied as-rolled, meaning no heat treatment. If you anneal or normalize it, the yield strength can change.
  • Cold working: Bending, rolling, or cold-forming increases yield strength but reduces ductility. This is why cold-rolled bars of A36 can show higher yield than hot-rolled.
  • Chemical composition: Small variations in manganese and carbon content within the ASTM limits affect strength.

If you need a guaranteed higher yield strength, you should specify a different grade like A572 Grade 50. Do not assume A36 will always be stronger than its minimum.

Welding and Fabrication Considerations

A36 is one of the easiest steels to weld. Its low carbon content (typically 0.25–0.29% max) means it rarely requires preheating or post-weld heat treatment for sections under about 1 inch thick. Common filler metals include E7018 and ER70S-6. For thicker sections, preheating to 100–150°F (38–66°C) can help avoid cracking.

Machining A36 is straightforward but can be slightly gummy compared to free-machining steels like 12L14. For high-volume machining, you might prefer a cold-rolled 1018 or a leaded steel. Cutting, shearing, and punching are all easy with standard equipment.

One common misconception is that A36 is “mild steel” and therefore weak. In reality, it is a structural grade with a well-defined minimum strength. It is not the strongest steel, but it is strong enough for most building and fabrication uses when designed correctly.

Cost and Availability

A36 is among the least expensive structural steels. Its price per pound is typically 10–20% lower than A572 Grade 50 and significantly lower than stainless or alloy steels. Availability is excellent: almost any steel supplier stocks A36 in plates, bars, angles, channels, and beams. For small projects, you can buy it in cut-to-size pieces from online metal retailers.

Because it is so common, lead times are short. This makes it a default choice for prototypes, repairs, and one-off fabrications where cost matters more than weight savings.

Frequently Asked Questions

What does “A36” stand for?

The “A” refers to the ASTM designation for ferrous metals, and “36” is the minimum yield strength in ksi (thousands of psi). So A36 means a structural steel with a minimum yield of 36,000 psi.

Can A36 be used for outdoor structures?

Yes, but it will rust if left unprotected. You must paint, galvanize, or apply a weathering coating. Unlike COR-TEN (weathering steel), A36 does not form a stable patina on its own.

Is A36 the same as mild steel?

In common usage, yes—A36 is a type of mild steel (low-carbon steel). However, “mild steel” is a broad category that includes many grades. A36 is specifically the structural grade with a guaranteed yield strength.

What is the difference between A36 and A572 Grade 50?

A572 Grade 50 has a higher minimum yield strength (50,000 psi vs. 36,000 psi) and a slightly different chemical composition that allows for higher strength. It is often used for bolted or welded structures where weight savings are important.

Does A36 require preheating before welding?

For most sections under 1 inch, no preheat is needed. For thicker sections or in cold environments, a preheat of 100–150°F is recommended to prevent hydrogen-induced cracking.

Can I harden A36 steel?

A36 has too little carbon to be hardened by heat treatment. You can case-harden it (adding carbon to the surface) but that is rarely practical. For hardened parts, choose a higher-carbon steel like 1045 or a tool steel.

Related

How pages are sourced and corrected: Sources and editorial policy.