Yes, a band saw is the right tool for resawing lumber, and it is the most efficient and accurate way to split a thick board into thinner pieces along its width. Resawing on a band saw uses a narrow, continuous blade loop to cut with minimal kerf (waste) and can handle boards far wider than a table saw. Below is a detailed look at how resawing works, what to look for in a saw, and how to get clean, safe results.
What Does Resawing Mean and Why Do It?
Resawing is the process of cutting a board along its width (parallel to the grain) to produce two or more thinner boards from one thicker one. This is different from ripping, which cuts across the grain of a board’s face. Woodworkers resaw for several reasons:
- Bookmatched panels: Cutting a thick board into two thin slabs and opening them like a book creates a mirrored grain pattern, prized for cabinet doors and tabletops.
- Cost savings: Buying thick stock and resawing it into thinner pieces is often cheaper than buying multiple thin boards of the same species.
- Using offcuts: A thick scrap can yield usable thin stock for drawer sides, small boxes, or veneer.
- Making veneer: With a sharp, narrow blade and a tall fence, you can produce consistent veneer slices.
Unlike a table saw, which cuts a wide kerf (about 1/8 inch) and is limited by blade depth, a band saw’s blade is thin (typically 1/8 to 1/2 inch wide) and can cut through stock up to the saw’s resaw capacity—often 6 to 12 inches or more. The band saw also pushes the work down toward the table, making it safer for deep cuts.
How a Band Saw Resaws: Blade and Machine Basics
A band saw has a continuous loop of toothed steel that runs between two or three wheels. The blade travels downward through the table, so the workpiece is pushed against the fence and into the blade. For resawing, the key components are:
- Blade width: Wider blades (1/2 to 1 inch) resist twisting and follow a straight line better. Narrow blades (1/4 inch) can wander, especially in deep cuts.
- TPI (teeth per inch): For resawing, a low TPI (2 to 4) is best. Fewer, larger teeth clear sawdust efficiently and cut faster. A blade with 6 or more TPI will clog and burn in deep cuts.
- Blade tension: The blade must be tensioned properly—usually to the manufacturer’s recommended setting—to prevent flexing and drift.
- Guide bearings: Upper and lower guides keep the blade aligned. They should be set just off the blade’s sides and back to reduce friction while preventing twist.
- Fence: A tall fence (at least as tall as the board) supports the workpiece vertically. Many band saws have a resaw fence accessory that clamps to the table.
Most band saws have a maximum resaw height, which is the distance from the table to the upper blade guide. This determines the widest board you can cut. For example, a 14-inch band saw typically has a 6-inch resaw capacity, while a 17-inch saw may handle 12 inches.
Choosing a Band Saw for Resawing
If you plan to resaw regularly, consider these factors when selecting a saw:
- Resaw capacity: Measure the thickest board you’ll cut. If you work with 8/4 lumber (2 inches thick), a 6-inch capacity is fine. For 12/4 or larger, look for a saw with at least 10 inches.
- Motor power: A 1 to 1.5 HP motor is adequate for occasional resawing of softwoods and thin hardwoods. For frequent deep cuts in hardwoods, a 2 HP or larger motor is better. Underpowered saws stall easily.
- Blade availability: A saw that accepts 105-inch or 93-1/2-inch blades gives you more choices. Check the blade length before buying.
- Table size and tilt: A larger table (at least 14 x 14 inches) supports long boards. Tilt is less important for resawing, but a 45-degree tilt is common.
- Dust collection: Resawing produces a lot of sawdust. A 4-inch dust port is preferable to a 2-1/2-inch port.
For occasional resawing, a 14-inch saw with a 1 HP motor and a good blade can work. For serious work, consider a 17-inch or larger saw. Many woodworkers also add a riser block to a 14-inch saw to increase resaw capacity, but this reduces rigidity and may require a larger motor.
Setting Up for a Clean Resaw Cut
Proper setup is more important than the saw itself. Follow these steps for a clean cut:
- Install a sharp resaw blade. A new blade with 2-3 TPI and a positive hook angle is ideal. Dull blades burn and wander.
- Set blade tension. Use the tension gauge if available, or the flutter test: with the saw off, turn the upper wheel by hand and adjust tension until the blade just stops fluttering.
- Adjust the guides. Set the upper guide to just clear the workpiece. The side bearings should be 0.002-0.003 inches from the blade, and the rear bearing should be set back slightly so it only touches when the blade is pushed back.
- Set the fence. Use a tall auxiliary fence clamped to the table. Align it parallel to the blade. Check with a square against the table.
- Check for drift. Draw a straight line on a scrap piece and cut it. If the blade veers, adjust the fence angle slightly to compensate, or adjust the blade tracking.
- Feed slowly and steadily. Let the blade do the work. Pushing too hard causes the blade to bow and the cut to wander.
For very wide boards, some woodworkers use a “resaw king” blade with a low TPI and a wide body. These blades are designed for deep cuts and stay straight under load.
Common Problems and How to Fix Them
Even with good setup, you may encounter issues:
- Blade drift (cut veers off the line): This is usually due to a dull blade, incorrect tension, or a misaligned fence. Re-tension, sharpen or replace the blade, and adjust the fence to match the blade’s natural cut path.
- Burning or slow feed: Often caused by a dull blade, too many teeth per inch, or feeding too fast. Use a lower TPI blade and slow down your feed rate.
- Blade popping off wheels: Check tension and tracking. Ensure the blade is centered on the wheel crowns.
- Wavy or uneven cut: This happens when the blade is too narrow for the depth, or the guides are set too far from the blade. Use a wider blade and tighten guides.
- Stalling the motor: If the saw slows down, you are feeding too hard or the blade is dull. Ease up and let the blade cut.
One common misconception is that you need a special “resaw blade” to resaw. While there are blades marketed for resawing, any sharp, low-TPI blade with a wide body will work. The key is sharpness and proper tension.
Safety and Technique Tips
Resawing is safe when done correctly, but the blade is exposed. Follow these safety rules:
- Use a push stick or push block. Keep your fingers at least 6 inches from the blade. A push stick with a notch works well for thin stock.
- Never reach behind the blade. If you need to reposition, stop the saw.
- Wear eye protection and a dust mask. Resawing creates fine sawdust that can irritate lungs.
- Check the blade for cracks. A cracked blade can break and fly off. Inspect regularly.
- Use a featherboard. This holds the work against the fence and prevents kickback.
- Feed at a steady pace. Do not force the cut. If the saw labors, reduce feed pressure.
For very thin veneer (less than 1/8 inch), you may need a sled or a special thin-kerf blade. Some woodworkers use a “resaw sled” that holds the board vertically and slides through the blade. This is useful for cutting multiple slices from a single board.
Alternatives to a Band Saw for Resawing
If you don’t have a band saw, there are other ways to resaw, but each has trade-offs:
- Table saw: You can make multiple passes, raising the blade slightly each time, then finish with a handsaw. This wastes more material (kerf) and is slower. It also has a maximum depth of about 3 inches on a 10-inch saw.
- Circular saw: You can cut from both sides, but the cut will not be as clean, and you must be careful with depth.
- Handsaw (rip saw): A Japanese pull saw or a frame saw can resaw, but it is labor-intensive and requires skill. It produces a very smooth cut with minimal kerf.
- Planer: A thickness planer cannot resaw; it only smooths the face. You could plane a board down to thickness, but that wastes the excess as shavings.
For most woodworkers, a band saw is the best choice because it offers the best combination of speed, accuracy, and minimal waste.
Frequently Asked Questions
What is the best blade for resawing on a band saw?
The best blade is a wide (1/2 to 1 inch) blade with 2-3 TPI and a positive hook angle. A 3/4-inch blade with 3 TPI is a common all-around choice. Make sure it is sharp and designed for resawing, such as a “resaw king” or “wood slicer” blade.
Can I resaw on a 14-inch band saw?
Yes, a 14-inch band saw can resaw up to about 6 inches in height. With a riser block, you can increase that to 12 inches, but you may need a larger motor (1.5 HP or more) to handle deep cuts in hardwoods.
Why does my band saw blade drift to one side?
Drift is usually caused by a dull blade, incorrect tension, or a misaligned fence. First, check blade tension and sharpness. Then, adjust the fence to align with the blade’s natural cut path by making a test cut and tilting the fence slightly.
How do I get a smooth resaw cut?
Use a sharp, low-TPI blade, set proper tension, and feed the wood slowly and steadily. A fence that is perfectly parallel to the blade is essential. You can also use a “resaw sled” for very thin slices.
Is resawing dangerous?
Resawing is safe if you follow basic band saw safety: keep fingers away from the blade, use push sticks, wear eye protection, and never force the cut. The blade is exposed, so always be aware of its position.
Can I resaw with a table saw instead?
Yes, but it is less efficient. You can make multiple passes, but the kerf is wider (more waste), and the maximum depth is limited to about 3 inches. A band saw is generally safer and more accurate for resawing.
Related
- Pegasus Meaning & Mythology Symbolism
- Polynesian Trickster Gods: Myths & Mischief
- Polynesian Mythology Gods: Key Deities Explained
How pages are sourced and corrected: Sources and editorial policy.