OneStopList

Gods and goddesses

Apollo Photoelectric Smoke Detector: How It Works

Updated November 21, 2026

An Apollo photoelectric smoke detector is a fire-safety device that uses a light source and a light sensor to detect smoke particles, and it is a core product line from the British manufacturer Apollo Fire Detectors. Rather than using a radioactive material like some ionisation detectors, it works by scattering light off smoke particles entering a sensing chamber, which triggers an alarm when the scattered light reaches a photodiode.

Background of Apollo Fire Detectors

Apollo Fire Detectors Ltd, based in Havant, Hampshire, UK, has been designing and manufacturing fire detection and alarm equipment since the early 1980s. The company is best known for its addressable fire alarm systems, particularly the XP95, Discovery, and Soteria ranges. These systems are used in commercial, industrial, and residential buildings worldwide. The photoelectric smoke detector is one of the most common devices in these ranges, alongside heat detectors and multi-sensor detectors that combine both technologies.

The Apollo photoelectric detector is designed to meet international standards such as EN 54-7 (European standard for smoke detectors) and UL 268 (North American standard). The exact model and certification depend on the specific product variant, as Apollo produces both conventional (two-wire) and addressable (digital communication) versions. The addressable versions communicate with a control panel, allowing precise identification of which detector has activated.

How the Apollo Photoelectric Detector Works

The core principle is optical light scattering. Inside the detector housing, there is an infrared light-emitting diode (LED) and a photodiode (light sensor), arranged so that light from the LED does not normally reach the photodiode—typically at an angle of about 135 degrees or in a labyrinth design that blocks direct light.

  • Normal state: The LED pulses periodically, and the photodiode receives no light because the chamber geometry blocks the beam.
  • Smoke enters: When smoke particles enter the sensing chamber, they scatter the light from the LED in all directions.
  • Detection: Some of that scattered light hits the photodiode, generating a small electrical current.
  • Alarm decision: The detector’s electronics compare the signal to a threshold. If the scattered light level exceeds the threshold for a short period (to avoid false alarms from transient dust), the detector goes into alarm and sends a signal to the control panel.

This method is particularly responsive to slow, smouldering fires that produce large smoke particles (typically 0.3 to 10 micrometres), such as those from upholstery, wiring, or paper. It is less responsive to fast, clean-burning fires that produce very small particles, which is why many systems combine photoelectric with heat or ionisation detection.

How to Choose the Right Apollo Model

Apollo offers several photoelectric detector variants, and the right choice depends on your system type and environment. The main distinctions are:

  • Conventional vs. addressable: Conventional detectors (e.g., Apollo 65 series) are wired in a simple loop and only indicate a zone on the panel. Addressable detectors (e.g., XP95, Discovery, Soteria) have a unique address and report exact location.
  • Standard vs. high-sensitivity: The Discovery range includes an ‘Analogue’ photoelectric detector that can be set to different sensitivity levels via the control panel, useful for areas with high ceilings or airflow.
  • Base type: Apollo detectors mount on specific bases (e.g., standard base, relay base, or isolator base). The base determines wiring and auxiliary functions like remote LED output.
  • Environmental rating: For dusty or humid areas, Apollo offers detectors with IP ratings (e.g., IP23 or IP54) that resist ingress, but note that high dust can still cause false alarms.

Always match the detector to your existing control panel. Apollo’s addressable protocols are not interchangeable with other brands, so if you have a non-Apollo panel, you need a converter or a different detector brand.

Common Problems and Misconceptions

A frequent misconception is that a photoelectric detector is ‘better’ than an ionisation detector in all situations. In reality, they respond to different fire types. Photoelectric is better for smouldering fires, while ionisation is faster for flaming fires with tiny particles. Many modern detectors are multi-sensor, combining both to cover more scenarios.

Common practical problems include:

  • False alarms from steam or cooking: Photoelectric detectors can be triggered by steam from showers or cooking vapours, as these contain water droplets that scatter light similarly to smoke. Installing them away from kitchens and bathrooms helps.
  • Dust accumulation: Over time, dust inside the chamber can cause the detector to become more sensitive or even false alarm. Apollo recommends cleaning the detector by vacuuming the exterior and, if possible, the internal chamber, but never using water or solvents.
  • LED failure: The pulsing LED has a limited lifespan. Apollo detectors typically have a 10-year service life from manufacture, after which the device should be replaced, not repaired.
  • Incorrect base wiring: Reversing polarity or using the wrong base can prevent the detector from communicating. Always follow the wiring diagram in the installation manual.

Comparison with Other Detector Types

Apollo also makes heat detectors and multi-sensor detectors. Here is how they compare:

  • Photoelectric: Best for slow, smoky fires; low false alarm rate from cooking; responds to visible smoke.
  • Heat detector: Responds to temperature rise; immune to smoke and dust; used in kitchens, garages, and boiler rooms where smoke detectors would false alarm.
  • Multi-sensor (optical + heat): Combines both technologies; the control panel can use algorithms to reduce false alarms and improve response to both fire types. The Apollo Discovery range includes such devices.

For most indoor living areas, photoelectric is the recommended choice by fire safety organisations because it catches smouldering fires, which are common in homes and produce more smoke before flames.

Cost and Installation Considerations

Apollo photoelectric detectors are mid-to-high end in price. A single addressable detector costs roughly $20–$50 USD depending on the model and supplier, while conventional detectors are slightly cheaper. However, the total cost includes the control panel, wiring, and installation labour, which far exceeds the detector cost. For a small building, a full Apollo system might cost $1,000–$3,000 installed; for a large commercial site, it can run into tens of thousands.

Installation should be done by a qualified electrician or fire alarm engineer, as incorrect wiring can render the system non-functional. Detectors must be placed on ceilings or high on walls, at least 0.5 metres from walls and corners, and not within 1 metre of air vents. National codes (e.g., NFPA 72 in the US, BS 5839 in the UK) specify spacing and placement rules.

Safety and Maintenance

Regular testing is essential. Apollo detectors have a test button that simulates smoke by reflecting light into the sensor; pressing it should trigger the alarm. Test monthly. Clean the detector exterior with a vacuum brush every six months. Never paint over a detector, as paint blocks the smoke entry. Replace the detector after 10 years from the manufacturing date (printed on the device) or per local regulations, even if it appears to work.

If you have a monitored system, ensure the control panel is connected to a central station or at least a loud audible alarm. A detector that alarms but nobody hears is useless.

Frequently Asked Questions

Can I use an Apollo photoelectric detector with a non-Apollo control panel? No, not directly. Apollo addressable detectors use a proprietary protocol (e.g., XP95 or Discovery) that only works with Apollo or compatible panels. You would need a protocol converter or choose a different detector brand that matches your panel.

Why does my Apollo detector false alarm when I cook? Cooking oil vapours and steam contain droplets that scatter light just like smoke. Move the detector further from the kitchen, or install a heat detector in the kitchen itself. Also, ensure the detector is not directly above the stove.

How do I know if my Apollo detector is expired? Look for the manufacturing date code on the device label, usually a four-digit number indicating year and week (e.g., 2315 means week 15 of 2023). If it is more than 10 years old, replace it.

Can I clean the inside of the detector chamber? You can gently vacuum the external slots and, if accessible, the internal chamber with a soft brush attachment. Do not open the sealed chamber, use compressed air, or apply any liquid. If dust is heavy, replacement is safer.

Is a photoelectric detector enough for a bedroom? Yes, for bedrooms, a photoelectric detector is recommended because smouldering fires from mattresses or electrical wiring produce large smoke particles. However, for maximum protection, consider a multi-sensor detector that also senses heat.

Related

How pages are sourced and corrected: Sources and editorial policy.