OneStopList

Gods and goddesses

Apollo Conventional Smoke Detector Guide

Updated November 21, 2026

Apollo is a well-known British manufacturer of fire detection and alarm systems, and its conventional smoke detectors are designed to work with conventional fire alarm control panels, which use a simple on/off signal rather than the digital addressing of analog addressable systems. These detectors, such as the Apollo Series 65 and the newer XP95 and Discovery ranges, are widely used in commercial and industrial buildings because they are reliable, easy to install, and cost-effective for smaller installations.

What Does “Conventional” Mean in Fire Detection?

In a conventional fire alarm system, detectors are wired in parallel on a single circuit or “zone.” Each zone is connected to a control panel, which monitors the total current flowing through the circuit. When a detector activates, it changes the circuit’s electrical state (typically by closing a switch), and the panel identifies the zone but not the specific detector. This is different from addressable systems, where each device has a unique digital address and the panel can pinpoint the exact location of an alarm.

Apollo’s conventional detectors are designed to be compatible with a wide range of conventional panels from various manufacturers, as long as the panel’s voltage and current requirements match. They typically operate at 9-33V DC and use a standard base that allows for easy replacement or maintenance.

How Apollo Conventional Smoke Detectors Work

Apollo conventional smoke detectors use either ionization or photoelectric (optical) sensing technologies, depending on the model. Photoelectric detectors, which are the most common for general use, contain a light source and a light sensor. When smoke enters the detection chamber, it scatters the light, causing it to hit the sensor and trigger an alarm. Ionization detectors use a small radioactive source to ionize air in a chamber; smoke particles disrupt the ion flow, which is detected electronically. Apollo’s optical detectors are particularly effective at detecting slow, smoldering fires, while ionization models are better for fast-flaming fires.

When a detector senses smoke, it sends a signal to the control panel, which then activates the alarm sounders and possibly triggers other responses like shutting down air handling units or calling a monitoring station. Apollo detectors also have a built-in LED indicator that lights up when the detector is in alarm, helping to visually identify the source.

Apollo Conventional Detector Ranges

Apollo offers several families of conventional detectors, each with specific features and compatibility:

  • Series 65: One of Apollo’s longest-serving ranges, available in optical, ionization, and heat (rate-of-rise and fixed temperature) versions. They are known for their robust construction and are still widely used in existing installations.
  • XP95: This range is actually an addressable system, but Apollo also makes a conventional version of the XP95 detector that uses the same sensing technology but with conventional signaling. It is often used in marine and industrial applications due to its high reliability.
  • Discovery: This is Apollo’s premium addressable range, but again, conventional variants exist (like the Discovery optical detector) for use with conventional panels. These detectors offer advanced features like drift compensation and are designed for high-performance environments.

When selecting a detector, it’s crucial to match the detector to the panel’s specifications and the environment where it will be installed. For example, in a dusty workshop, a detector with a higher immunity to false alarms might be needed.

How to Choose the Right Apollo Conventional Detector

Choosing the right detector depends on the fire risks in the area you are protecting. Here are the main factors to consider:

  • Fire Type: For slow-burning, smoldering fires (e.g., from overheating electrical wiring), use an optical (photoelectric) detector. For fast-flaming fires (e.g., from flammable liquids), use an ionization detector. Many installations use a combination.
  • Environmental Conditions: In areas with high humidity, steam, or dust, optical detectors are less prone to false alarms than ionization ones. Heat detectors are best for kitchens or boiler rooms where smoke detectors would cause nuisance alarms.
  • Compatibility: Ensure the detector is compatible with your existing control panel. Check the panel’s manual for the recommended detector types and wiring specifications.
  • Certification: Look for detectors that meet relevant standards such as EN 54 (European) or UL (North American) for reliability and performance.

Installation and Maintenance

Proper installation is critical for detector performance. Apollo detectors are typically mounted on a standard base (like the Series 65 base) that is wired into the zone circuit. The detector head plugs into the base, making it easy to replace or clean. During installation, ensure that the wiring is correct and that the detector is not placed in areas with high airflow (e.g., near air vents) which could prevent smoke from reaching the sensor.

Maintenance involves regular cleaning and testing. Dust can accumulate inside the detection chamber, causing false alarms or reducing sensitivity. Apollo recommends cleaning detectors periodically using a vacuum cleaner or a soft brush. Testing should be done using a suitable aerosol smoke tester, not by open flames, to avoid damage. Always follow the manufacturer’s instructions and local fire codes.

Common Problems and Troubleshooting

Even reliable detectors can experience issues. Common problems include:

  • False Alarms: Often caused by dust, insects, or steam. Cleaning the detector and checking the environment can resolve this. If the problem persists, the detector may need replacing.
  • Detector Not Responding: Check the wiring, base connections, and whether the detector is properly seated. Also, verify that the zone is not already in alarm or fault.
  • Intermittent Faults: Loose connections or corroded terminals can cause intermittent issues. Inspect the wiring and replace any damaged components.

If you are unsure about a problem, consult a qualified fire alarm engineer. Never attempt to bypass or disable a detector, as this could lead to a serious safety hazard.

Apollo Conventional vs. Addressable Systems

The main difference between conventional and addressable systems is the level of detail in alarm reporting. Conventional systems indicate only the zone, while addressable systems identify the exact device. Addressable systems also allow for more complex programming, such as adjusting sensitivity per detector and providing more detailed fault diagnostics. However, conventional systems are simpler, less expensive, and easier to install, making them ideal for small to medium-sized buildings. Apollo offers both types, so the choice depends on your budget and the complexity of the building.

Cost and Availability

Apollo conventional smoke detectors are generally affordable, with prices varying depending on the model and supplier. A typical optical detector might cost between $20 and $50, while heat detectors are usually cheaper. The bases and accessories add a small additional cost. They are widely available from fire safety equipment suppliers, both online and in physical stores. When purchasing, ensure you buy from a reputable supplier to guarantee genuine Apollo products, as counterfeit or incompatible devices can be dangerous.

Safety and Compliance

All fire detection equipment must be installed and maintained in accordance with local fire safety regulations and standards, such as NFPA 72 in the US or BS 5839 in the UK. Apollo detectors are designed to meet these standards, but it is your responsibility to ensure the system is correctly designed and tested. Regular testing and record-keeping are essential. Always consult with a certified fire safety professional for installation and maintenance to ensure your system is fully compliant and effective.

Frequently Asked Questions

Can I use an Apollo conventional detector with any fire alarm panel?

Not necessarily. While Apollo detectors are designed to be compatible with many conventional panels, you must check the panel’s specifications for voltage, current, and wiring requirements. Using an incompatible detector can cause false alarms or failure to detect a fire.

How often should I test my Apollo smoke detector?

You should test your smoke detector at least once a month using a test button or an approved smoke tester. Additionally, have a professional inspect the entire system annually to ensure it meets code and is in good working order.

What is the lifespan of an Apollo conventional smoke detector?

Most smoke detectors, including Apollo’s, have a recommended lifespan of about 10 years. After that, the sensor may become less sensitive, so it’s best to replace the detector head, even if it appears to work.

Can I clean my Apollo detector myself?

Yes, you can gently vacuum the exterior and the detection chamber openings. However, do not open the chamber or use liquids. If the detector is still dirty or faulty, replace it.

Are Apollo conventional detectors suitable for home use?

Yes, they can be used in homes, but they are more commonly found in commercial settings. For home use, you might find simpler, battery-operated detectors that are easier to install. However, if you have a wired alarm system, Apollo detectors can be a reliable choice.

Related

How pages are sourced and corrected: Sources and editorial policy.