OneStopList

Gods and goddesses

Are Kitchen Mixer Taps a Standard Size?

Updated November 20, 2026

Yes, kitchen mixer taps are largely standardised in their fixing hole size and pipe connections, but the overall dimensions vary widely. The most common standard is a 35mm fixing hole and 15mm or 22mm pipe inlets, yet the height, spout reach, and projection of the tap itself are not standardised.

What Does “Standard Size” Actually Mean for a Mixer Tap?

When people ask if kitchen mixer taps are a standard size, they usually mean one of three things: the hole in the worktop or sink, the pipe connections underneath, or the physical dimensions of the tap body. Each of these is governed by different conventions.

  • Fixing hole diameter: Most UK and European kitchen mixer taps use a 35mm hole. This is the most consistent standard across brands.
  • Pipe inlet size: The flexible tails that connect to your water supply are typically 15mm (half-inch) in the UK and Europe, or 3/8-inch in the US. Some high-flow taps use 22mm.
  • Tap body dimensions: Height, spout reach, and spout height are not standardised. They vary by design, from compact 150mm-high taps to tall gooseneck models over 400mm.

Why the 35mm Hole Became the Standard

The 35mm fixing hole is a de facto industry standard, not a legal requirement. It originated from the need to fit both the tap body and the securing nut underneath. Most sinks and worktops are pre-drilled with either a single 35mm hole or a set of holes (often 2 or 3) spaced 100mm apart for separate hot and cold taps or a mixer with a side sprayer.

If you are replacing an existing mixer tap, the new one will almost certainly fit the same 35mm hole. However, if you have an older sink or a worktop with a different hole size (e.g., 28mm or 40mm), you may need an adapter plate or a new sink.

Pipe Connections: 15mm vs 22mm

The tails that connect the tap to your plumbing are usually 15mm compression fittings in the UK and Europe. In the US, the standard is 3/8-inch. Some high-end or high-flow kitchen taps use 22mm tails to deliver more water per minute, but these are less common.

If you are replacing a tap, check the existing pipework. Most modern taps come with flexible tails that have 15mm connectors. If your pipes are 22mm, you will need a reducing adapter. Conversely, if your tap has 22mm tails and your pipes are 15mm, you can use a reducing coupler.

How to Choose the Right Size for Your Kitchen

Choosing the right mixer tap size involves more than just the hole and pipe connections. The physical dimensions affect both function and aesthetics.

  1. Measure the fixing hole: Use a ruler or calliper to check the diameter. If it is 35mm, you have the standard.
  2. Check the spout height: For a deep sink, you need a tap with a high spout (at least 200mm) so you can fill pots and pans. For a shallow sink, a lower spout is fine.
  3. Consider spout reach: The distance from the base to the spout outlet should be enough to reach the centre of your sink. Typically, 200-230mm is adequate for a standard 500mm sink.
  4. Check the deck thickness: The tap’s fixing bolt must be long enough to pass through your worktop. Most taps fit worktops up to 40mm thick, but some are longer.

Common Problems When Sizes Don’t Match

Even with standard sizes, you can run into issues. Here are the most frequent problems and their solutions:

  • Hole too large: If your existing hole is 40mm and the new tap needs 35mm, use a reducing plate or a rubber grommet.
  • Hole too small: You can carefully enlarge the hole with a hole saw, but this is permanent. Alternatively, choose a tap with a smaller base.
  • Pipework mismatch: If your pipes are 22mm and the tap tails are 15mm, use a reducing coupler. If the tails are too short, extend them with a flexible hose.
  • Spout too short: A tap with a 150mm spout will splash water over the back of a deep sink. Measure your sink depth first.

Cost Implications of Non-Standard Sizes

Standard-size taps are cheaper because they are mass-produced. A basic 35mm mixer tap can cost from £30 to £100. Non-standard sizes, such as those with 28mm holes or 22mm tails, are less common and may require adapters, adding £10-£30 to the total cost. If you need a custom height or reach, you may have to look at premium brands, which can cost £200 or more.

Safety and Installation Considerations

When installing a mixer tap, always turn off the water supply at the isolation valve or the main stopcock. Use PTFE tape on the threads of the tails to prevent leaks. If you are unsure about the pipework, consult a professional plumber. Also, check that the tap is suitable for your water pressure: some taps require a minimum of 1.0 bar, while others work with low pressure systems. Incorrect pressure can cause poor flow or noise.

Frequently Asked Questions

Are all kitchen mixer taps the same hole size?
No, but the vast majority use a 35mm hole. Some older taps or specialised models use 28mm, 32mm, or 40mm. Always measure before buying.

Can I replace a mixer tap without changing the sink?
Yes, if the new tap fits the existing hole and pipe connections. If the hole is larger, use an adapter plate. If the pipes are different sizes, use reducing couplers.

Do mixer taps come with flexible tails?
Most modern taps do come with flexible tails, usually 500mm long. If they are too short, you can extend them with a flexible hose and connectors.

What is the standard distance between hot and cold taps?
For separate taps, the standard spacing is 100mm (4 inches) between centres. For a mixer tap, it is a single hole, so spacing is irrelevant.

Are US and UK mixer taps the same size?
Not exactly. US taps often use 3/8-inch pipes and 1.5-inch holes, while UK taps use 15mm pipes and 35mm holes. However, many modern taps are designed to fit both with adapters.

Does the spout height matter for a kitchen sink?
Yes. A low spout (under 150mm) may not allow you to fill a large pot. For a deep sink, choose a tap with at least 200mm spout height.

Related

How pages are sourced and corrected: Sources and editorial policy.