OneStopList

Gods and goddesses

Which Meter Function Has a Fuse? Multimeter Guide

Updated November 20, 2026

The current (amps) function on a multimeter is the one that has a fuse in its circuit. When you turn the dial to measure AC or DC current (usually marked with an “A” and a wavy or straight line), the meter routes the test current through a fuse, typically rated at 10A or 400mA, to protect the meter and you from overcurrent damage.

Why the Current Function Needs a Fuse

Voltage and resistance measurements are made in parallel with the circuit, meaning the meter draws only a tiny amount of current. Current measurement, however, is done in series: the meter becomes part of the circuit, and all the current flowing through the load must pass through the meter’s internal shunt and fuse. If you accidentally connect the meter across a power source while it is set to measure current, the meter becomes a near-short circuit. Without a fuse, the internal shunt wires and the test leads would heat up instantly, potentially melting insulation, starting a fire, or causing an arc flash. The fuse is a sacrificial element that blows quickly, breaking the circuit and preventing damage to the meter and injury to the user.

Fuse Ratings and Sizes in Multimeters

Most digital multimeters have two separate current inputs and two corresponding fuses. The common arrangement is:

  • High-current fuse (10A): Used for the 10A or 20A input jack, typically a ceramic body fuse rated 10A, 600V or 1000V, often with a high breaking capacity (e.g., 10kA).
  • Low-current fuse (400mA or 500mA): Used for the mA/µA input jack, usually a smaller ceramic fuse rated 400mA or 500mA, 250V or 600V.

These are not standard glass fuses you find in household electronics. They are specifically rated for high voltage and high interrupting capacity. Using a regular glass fuse is dangerous because it may not blow fast enough or may shatter, leaving live parts exposed. Always replace a blown multimeter fuse with the exact type and rating specified in the meter’s manual.

How to Tell if the Fuse Is Blown

The most obvious sign is that the meter reads zero or shows an overload (“OL” or “1”) when measuring a current that should be flowing. To confirm, follow this safe test:

  1. Turn the meter off and remove the test leads.
  2. Open the battery compartment; the fuses are usually visible there or behind a separate panel.
  3. Visually inspect the fuse. A blown fuse often has a broken wire, a dark smear, or a cloudy window.
  4. Use the meter’s continuity or resistance mode to test the fuse. Place one probe on each end of the fuse. A good fuse will show near-zero resistance or a beep; a blown fuse will show “OL” or no beep.

Some meters have a separate fuse test function, but the continuity check works universally.

Common Misconceptions About Fuses in Multimeters

Many people assume the resistance (Ω) or voltage (V) function has a fuse because they see the fuse symbol printed near the dial. That symbol actually indicates the meter’s internal protection rating, not that the fuse is in that circuit. Voltage and resistance inputs are protected by high-impedance circuitry and sometimes by a PTC (positive temperature coefficient) thermistor, not a fuse. Another misconception is that a blown fuse means the meter is broken. It is a normal safety event; replacing the fuse restores full function. Also, some cheap meters use a single fuse for both current jacks, but the vast majority of quality meters use two separate fuses.

How to Choose a Replacement Fuse

When buying a replacement, you need to match three things: current rating, voltage rating, and physical size. The current rating is printed on the fuse body (e.g., 10A, 400mA). The voltage rating is equally important—a 250V fuse in a 600V meter can arc over internally. The physical size determines whether it fits the holder; common sizes are 5x20mm and 6x32mm. Check the meter’s manual for the exact part number. Many manufacturers (Fluke, Keysight, Extech) sell fuse kits specifically for their models. Using a fuse with a higher current rating than specified defeats the protection; using a lower rating causes nuisance blows.

Safety Rules for Measuring Current

Current measurement is the most dangerous function on a multimeter. Follow these rules to avoid blowing fuses or causing injury:

  • Always connect the meter in series with the load, never in parallel with a voltage source.
  • Start with the highest current range and the high-current input jack if you are unsure of the expected current.
  • Never switch the rotary dial while the test leads are connected to a live circuit.
  • Use test leads with proper safety ratings (CAT III or CAT IV) and shrouded connectors.
  • If the meter reads “OL” on the mA range, immediately disconnect and switch to the 10A range.
  • Never measure current in a circuit that could exceed the fuse’s rating, even on the 10A range.

Frequently Asked Questions

Can I test a fuse with a multimeter? Yes. Set the meter to resistance or continuity mode, place the probes on both ends of the fuse, and check for a low reading or beep. This works for any fuse, not just the ones inside the meter.

Why does my multimeter show “OL” when measuring current? “OL” means overload, which can indicate a blown fuse, an open circuit, or that the current exceeds the selected range. If the circuit is working and you are on the correct range, the fuse is likely blown.

Is it safe to use a car fuse in a multimeter? No. Car blade fuses are not designed for high-voltage interruption and may not blow fast enough. They also do not fit the meter’s fuse holder. Always use the specified ceramic fuse.

Does the voltage function have a fuse? No, the voltage function is protected by high-impedance input circuitry, not a fuse. The fuse symbol near the dial refers to the meter’s overall protection rating, not a specific fuse in that circuit.

How often should I replace the fuses in my multimeter? Only when they blow. There is no maintenance schedule for fuses; they are sacrificial components. If you never measure current incorrectly, they can last the lifetime of the meter.

Can I measure current with a clamp meter instead? Yes, a clamp meter measures current without breaking the circuit and without using a fuse, because it uses a magnetic sensor around the conductor. This is safer for high currents and is the preferred method for live wires.

Related

How pages are sourced and corrected: Sources and editorial policy.