OneStopList

Gods and goddesses

Apollo Oil Tank Monitor Troubleshooting Guide

Updated November 20, 2026

Apollo oil tank monitors can fail to report, show error codes, or give inaccurate readings; the most common fixes involve checking the sensor wiring, replacing the battery, and resetting the transmitter. Start by identifying your model (most are Apollo G6, G6B, or LITE), then work through the power and signal checks below before calling a technician.

How Apollo Oil Tank Monitors Work

Apollo monitors use a float-based sensor that sits inside the oil tank, attached to a transmitter that sends data to a receiver plugged into a wall socket in your home. The transmitter uses a 433 MHz radio signal to report the tank level, typically every 15 minutes or when the level changes by a set amount. The receiver displays the level as a percentage or in litres, and some models connect to the Apollo Smart app for remote viewing.

The system is battery-powered on the transmitter side, with a long-life lithium battery (often lasting 3–5 years). The receiver is mains-powered. Because the transmitter is sealed and mounted on the tank, most faults are either battery depletion, wiring corrosion, or a lost radio link between transmitter and receiver.

Common Error Codes and Their Meanings

Apollo receivers show a small set of error messages. Knowing what each means saves time:

  • “No Signal” or “– – –” – the receiver has not heard from the transmitter for over a set period (usually 2–4 hours). This is the most common fault and usually means the transmitter battery is dead, the transmitter is out of range, or the receiver is unplugged.
  • “Err” or “E1” – a sensor fault, often caused by a broken float arm or a short in the sensor cable inside the tank.
  • “Low Battery” – the transmitter battery is below the threshold; replace it soon.
  • “Full” or “Empty” stuck – the float may be stuck against the tank wall or the sensor arm may be bent.

Step-by-Step Troubleshooting

Work through these steps in order. Most issues are resolved at step 2 or 3.

  1. Check the receiver – confirm it is plugged in and the power light is on. Move it closer to the tank temporarily to rule out range issues (typical range is 50–100 metres in open air, but walls and metal tanks reduce this).
  2. Replace the transmitter battery – the transmitter has a small compartment, usually requiring a CR123A or similar lithium cell. Replace it with the same type, and press the reset button if present. This fixes the majority of “No Signal” faults.
  3. Inspect the sensor cable – at the tank top, check the cable from the transmitter to the float sensor for cuts, corrosion, or loose connections. Clean any white or green corrosion with a dry cloth and re-seat the connector.
  4. Reset the system – on the receiver, press and hold the reset button for 10 seconds, then re-pair with the transmitter by pressing the transmitter’s pairing button (see your manual for the exact sequence).
  5. Test the float manually – with the tank lid off (only if safe and the tank is not pressurised), gently lift the float arm and see if the receiver updates. If it does not, the sensor is faulty.

Battery and Signal Issues Explained

The transmitter battery is the weakest link. Apollo states the battery lasts up to 5 years, but cold weather and frequent transmissions can shorten that. If you have had the unit for over 3 years and see “Low Battery” or intermittent signals, replace the battery first. Use only the specified lithium type – alkaline cells do not handle cold temperatures well and may leak.

Signal loss is also common in houses with thick stone walls or where the tank is in a detached garage or underground. If the receiver is more than 50 metres from the transmitter, or if a metal tank acts as a Faraday cage, the signal may not reach. A simple test: temporarily place the receiver right next to the tank (using an extension lead) and see if it connects. If it does, you need to reposition the receiver or add a signal repeater (Apollo sells a range extender).

When to Call a Professional

If you have replaced the battery, cleaned the connections, and reset the system but still see an error, the fault is likely internal. Do not open the transmitter or receiver case – they are sealed for weatherproofing. Contact a heating engineer or Apollo’s support line. Also call a professional if you suspect the float is stuck inside the tank, as opening a fuel tank requires proper safety procedures (no naked flames, no smoking, and the tank should be vented).

Do not attempt to repair the sensor cable inside the tank yourself. Oil tanks are not pressurised, but the oil is flammable, and any spark from a tool could ignite vapours. A qualified technician can drain the tank or use a tank-safe camera to inspect the float.

Apollo G6 vs G6B vs LITE – Differences That Matter

Apollo’s current range has three main models, and troubleshooting steps differ slightly:

  • G6 – the standard model with a wired float sensor, works with the Apollo Smart app via a Wi-Fi hub (sold separately).
  • G6B – same as G6 but with a built-in battery backup for the receiver, so it keeps displaying during a power cut.
  • LITE – a budget version with a simpler receiver, no app connectivity, and a shorter battery life on the transmitter.

For all three, the transmitter battery replacement procedure is identical. The receiver reset button location differs – on the LITE it is on the back, while on the G6 it is under the front flap. Check the manual that came with your unit or the label on the back of the receiver for the model number.

Preventive Maintenance Tips

To avoid future faults, adopt a simple routine:

  • Replace the transmitter battery every 3 years, regardless of warnings.
  • Inspect the cable gland at the tank top annually for cracks or water ingress.
  • Keep the receiver away from large metal objects and Wi-Fi routers, which can interfere with the 433 MHz signal.
  • If you have an underground tank, check the cable conduit for water accumulation – moisture in the conduit is a common cause of sensor corrosion.

Frequently Asked Questions

Why does my Apollo monitor show “No Signal” after a power cut?
The receiver may have lost its pairing with the transmitter. Press the reset button on the receiver, then press the pairing button on the transmitter (usually a small recessed button) within 30 seconds. If that fails, replace the transmitter battery – power cuts often coincide with a weak battery that finally gives out.

Can I use a normal AA battery in the Apollo transmitter?
No. The transmitter requires a specific lithium battery (typically CR123A or CR2, depending on model). Using an alkaline AA will not fit and may damage the contacts. Check the battery type printed inside the transmitter compartment.

How accurate is the Apollo oil level reading?
The float sensor gives a reading accurate to roughly ±5% of the tank capacity. It is designed to tell you whether you have a quarter, half, or three-quarters full, not to measure exact litres. For precise delivery planning, note that the reading lags slightly when oil is being used quickly.

What does the red light on the receiver mean?
A solid red light usually indicates a low transmitter battery or a sensor fault. A flashing red light often means the receiver has not received a signal for over 24 hours. Refer to the model-specific LED chart on the receiver’s label – the meanings are printed there.

Can I test the sensor without opening the tank?
Yes. On most models, you can disconnect the sensor cable at the transmitter and connect a small resistor (simulating a full tank) to see if the receiver responds. This is a diagnostic trick used by installers, but it requires a multimeter and the correct resistor value – if you are not confident, skip it and call a technician.

Related

How pages are sourced and corrected: Sources and editorial policy.