OneStopList

Gods and goddesses

Primer for Drilling on the Lathe: How to Do It Right

Updated November 18, 2026

Drilling on the lathe is the process of creating a centered hole in a rotating workpiece using a drill bit held in the tailstock. The lathe is the most accurate way to drill a hole that is perfectly concentric with the outside of the part, because the workpiece rotates around its true center while the bit feeds in along that same axis.

Why Drill on a Lathe Instead of a Drill Press?

A drill press holds the workpiece still and rotates the bit. The bit can wander, especially when starting on a curved surface, and the hole may end up off-center relative to the part’s outer diameter. On a lathe, the workpiece spins and the bit is stationary, so the hole is automatically centered on the axis of rotation. This is essential for operations like turning a shaft that must have a center hole, boring a cylinder for a bearing, or threading a hole that must align with the part’s symmetry.

Another advantage is that the lathe’s tailstock provides a rigid, controlled feed. You can advance the bit slowly and steadily, which produces a cleaner hole and reduces the risk of the bit grabbing or breaking. For deep holes, you can also use a pilot drill and then a larger bit, or a boring bar, all without re-chucking the workpiece.

Essential Tools and Setup

Before you start, you need the right equipment and a clean, secure setup. The basic list includes:

  • Tailstock with a drill chuck: Most lathes have a Morse taper in the tailstock spindle. You can mount a keyed drill chuck directly or use a chuck with a Morse taper shank that matches the tailstock.
  • Center drill (combined drill and countersink): This is a short, stiff bit that creates a small pilot hole and a 60-degree countersink in one step. It prevents the larger drill from wandering and gives the tailstock center a seat.
  • Standard twist drill bits: For holes up to about 1/2 inch (12 mm), a good quality HSS bit is fine. For larger holes, you may need a reduced-shank bit (often called a Silver & Deming bit) that fits in a standard chuck.
  • Cutting fluid or lubricant: Use a suitable cutting oil for steel, or a water-soluble coolant for aluminum. This reduces heat and improves chip flow.
  • Deburring tool: To remove sharp edges after drilling.

Mount the workpiece securely in a chuck or collet. If the part is long, support the free end with a live center in the tailstock, but remove that center before you begin drilling. Always check that the tailstock is aligned with the headstock spindle—most lathes have a center mark on the bed, but you can verify by bringing the tailstock center up to the headstock center and checking they meet exactly.

Step-by-Step Drilling Process

Here is the standard procedure for drilling a centered hole on a lathe:

  1. Face the workpiece: If the end of the part is rough or not square, take a light facing cut to create a flat surface perpendicular to the axis. This gives the drill a clean start.
  2. Center drill: Install a center drill in the tailstock chuck. Bring the tailstock up so the drill is close to the work, then start the spindle at a moderate speed (about 1,000–1,500 RPM for small parts in mild steel). Feed the center drill in slowly with the tailstock handwheel. You only need a small pilot hole, about 1/8 inch (3 mm) deep, and the countersink should just touch the surface.
  3. Peck drill: Replace the center drill with the actual drill bit. Set the spindle speed according to the bit diameter and material (see below). Start the spindle, then feed the bit in using the tailstock handwheel. For holes deeper than about 3 times the bit diameter, pull the bit out periodically to clear chips. This is called peck drilling and prevents chip packing and overheating.
  4. Clear chips: When you retract the bit, use a brush or air to clear chips from the flutes. Never use your fingers while the spindle is turning.
  5. Deburr: After the hole is through, use a deburring tool or a countersink to remove the sharp edge on both sides if accessible.

For through holes, you may notice a slight burr on the back side when the bit breaks through. Reduce feed pressure near the end to minimize this.

Choosing the Right Speed and Feed

The correct spindle speed depends on the material and the drill diameter. The general formula for HSS drill bits is: RPM = (CS × 4) / D, where CS is the cutting speed in surface feet per minute (SFM) and D is the drill diameter in inches. For metric, use RPM = (CS × 1000) / (π × D) with CS in meters per minute and D in millimeters.

Typical cutting speeds for HSS drills:

  • Aluminum: 200–300 SFM (60–90 m/min)
  • Brass and bronze: 150–200 SFM (45–60 m/min)
  • Mild steel: 80–100 SFM (25–30 m/min)
  • Stainless steel: 40–60 SFM (12–18 m/min)
  • Cast iron: 50–80 SFM (15–25 m/min)

For example, a 1/4-inch drill in mild steel: RPM = (90 × 4) / 0.25 = 1,440 RPM. A 1/2-inch drill in the same material: RPM = (90 × 4) / 0.5 = 720 RPM. Slower for larger bits, faster for smaller ones.

Feed rate is harder to quantify. For most small lathes, a hand feed of about 0.001–0.005 inches per revolution (0.03–0.13 mm/rev) is safe. You want a steady, continuous cut, not a forced one. If the bit squeals or smokes, reduce speed or feed, and check the cutting fluid.

Common Problems and How to Avoid Them

Even with the right setup, issues can arise. Here are the most frequent problems and their solutions:

  • Drill wandering off-center: This is almost always due to not using a center drill first. A twist drill will not start accurately on a flat surface. Always use a center drill or a spotting drill.
  • Drill bit breaking: Usually caused by too high a feed, too low a speed, or not pecking to clear chips. If the bit grabs, it can snap. Use a slower feed and more pecks.
  • Hole not straight: If the tailstock is not aligned with the headstock, the hole will be angled. Check alignment with a test bar or by bringing centers together. Also, a bent drill bit will cause a crooked hole.
  • Chatter or vibration: This can happen if the workpiece is not rigidly supported or if the drill bit is too long. Use a stubby drill or a pilot hole, and make sure the tailstock is locked down.
  • Overheating: Excessive heat ruins drill bits and workpieces. Use cutting fluid and peck to allow cooling. If the bit turns blue, it has lost its temper and should be replaced.

Drilling Deep Holes and Large Diameters

For holes deeper than about 4 times the diameter, standard twist drills become less effective because chips cannot escape easily. You can still drill them with frequent pecking and a coolant, but the hole may drift. For precision deep holes, a gun drill or a boring head is used, but these are advanced techniques.

For large holes (over 1 inch / 25 mm), a twist drill is inefficient and may require too much thrust. Instead, drill a pilot hole (about 1/4 the final diameter) and then use a boring bar to enlarge the hole to size. Boring also gives a better surface finish and can correct any minor misalignment.

Safety Considerations

Lathe drilling is safe if you follow basic rules:

  • Always wear safety glasses. Chips can fly at high speed, especially when drilling brass or cast iron.
  • Remove chuck keys and wrenches before starting the spindle.
  • Never clear chips by hand. Use a brush or a chip hook while the spindle is stopped.
  • Secure long workpieces. Use a steady rest if the part extends far from the chuck, or support the end with a center while drilling (but remove the center before the drill reaches it).
  • Tie back long hair and loose clothing. Rotating machinery can catch anything dangling.
  • Do not use a drill bit that is too long for the job. Long bits flex and can break, sending fragments flying.

Also, be aware of the tailstock quill travel. If you extend the quill too far, it can slip or jam. Keep the quill within its normal range, and lock the tailstock to the bed when drilling.

Frequently Asked Questions

Can I drill on a wood lathe? Yes, but the technique is the same. Wood drills at higher speeds (1,500–3,000 RPM) and you do not need cutting fluid. Use a brad-point drill for cleaner holes.

Do I need a center drill for every hole? For holes up to about 1/4 inch (6 mm), a center drill is still recommended because it prevents the bit from skating. For very small holes (under 1/16 inch), you can use a spotting drill instead. For holes that are not critical, you might skip it, but you risk an off-center hole.

What is the difference between a center drill and a spotting drill? A center drill has a 60-degree countersink and a small pilot, designed to create a seat for a lathe center. A spotting drill has a 90-degree or 120-degree point and is used only to start a hole, without the countersink. For drilling on a lathe, a center drill is the standard choice because it also provides a chamfer that helps guide the drill.

How do I drill a hole that is not in the center? If you need an off-center hole, you cannot use the tailstock directly. You can use a four-jaw chuck and dial in the offset, or use a milling attachment. For a single off-center hole, it is often easier to drill it on a drill press or mill.

Why does my drill bit make a squealing noise? Squealing usually means the drill is rubbing instead of cutting. This happens when the speed is too low, the feed is too light, or the bit is dull. Increase speed slightly or increase feed, and check the cutting edge.

Can I use a twist drill to enlarge an existing hole? Yes, but the drill will follow the existing hole, which is fine if the hole is already centered. If you need to move the hole, use a boring bar instead.

Related

How pages are sourced and corrected: Sources and editorial policy.