Yes, Infinity Tools makes carbide tipped replacement knives specifically for the Dewalt 734 planer, and they are a popular upgrade over the stock high-speed steel (HSS) blades. These aftermarket knives fit the DW734 and the older DW733 models, offering significantly longer edge life and better performance on abrasive or knotty wood.
Background: Why Replace the Stock Knives?
The Dewalt 734 planer ships with double-sided HSS knives. HSS is fine for occasional use on clean softwood, but it dulls quickly on plywood, MDF, or any wood with dried glue or embedded grit. Once dull, the planer tears grain, leaves burn marks, and requires more effort to push stock through. Many woodworkers switch to carbide-tipped knives because the carbide edge can last 5–10 times longer than HSS, especially when planing materials that would quickly wreck a steel edge.
Infinity Tools is a well-known aftermarket manufacturer that produces carbide-tipped planer knives for many popular machines, including the Dewalt 734. Their knives are not OEM (original equipment manufacturer) parts, but they are designed to the same dimensions and fit the cutter head without modification.
How Carbide-Tipped Knives Work
Carbide-tipped knives have a body made of steel (for strength and easy mounting) with a thin layer of tungsten carbide brazed onto the cutting edge. Tungsten carbide is extremely hard—much harder than HSS—so it resists abrasion and stays sharp longer. The trade-off is that carbide is more brittle; it can chip if you hit a nail or a large knot, whereas HSS might just dull.
For the Dewalt 734, the knives are double-sided, meaning you can flip them to use the second edge before needing to replace them. The Infinity version uses a micro-grain carbide that is tougher than standard carbide, reducing the risk of chipping. The cutting edge is honed to a sharp finish, and the knife is precision ground to match the Dewalt’s cutter head geometry.
Choosing the Right Knife for Your Dewalt 734
When shopping for replacement knives, you need to match the exact dimensions and hole pattern of the Dewalt 734. The stock knives are approximately 12-1/4 inches long, 1/2 inch wide, and 1/8 inch thick, with two mounting slots. Infinity Tools lists their knives as fitting both DW734 and DW733, so you can check compatibility before ordering.
There are two main types of carbide knives available:
- Standard carbide: Good for general use, affordable, and long-lasting.
- Micro-grain carbide (like Infinity’s): More resistant to chipping, better for heavy use or planing dirty wood.
You might also see “helical” or “spiral” cutter heads as an alternative, but those require a full cutter head replacement, not just new knives. If you want to keep the original cutter head, stick with straight carbide knives.
Installation and Setup
Installing new knives on the Dewalt 734 is straightforward, but you must be careful to set the knives at the correct height. The DW734 uses a jack screw system with a gauge (included with the planer) to set the knife height. Here’s the general process:
- Unplug the planer and remove the dust chute to access the cutter head.
- Loosen the two cap screws that hold the knife in place (there are two per knife).
- Slide the old knife out and clean the slot and the gib (the metal bar that clamps the knife).
- Insert the new knife with the carbide edge facing up and outward.
- Use the included gauge to set the knife height, then tighten the screws evenly.
- Rotate the cutter head to the next knife and repeat.
It’s important to tighten the screws in small increments and check the height with the gauge at both ends of the knife. An uneven knife will cause a poor finish and can be dangerous. If you’ve never changed planer knives, watch a tutorial or consult your manual—it’s not difficult, but accuracy matters.
Common Problems and Solutions
One common issue is that aftermarket knives may not seat perfectly in the slot. This is rare with Infinity knives, but if you notice the knife rocking, check for burrs on the gib or the slot. Clean them with a file or fine sandpaper.
Another problem is that carbide knives can chip if you hit a nail or a staple. If a chip appears, you can often rotate the knife to a fresh edge, but if the chip is large, you’ll need to replace the knife. Some users report that carbide knives produce a slightly rougher finish than HSS on very soft woods, but this is usually negligible and can be fixed with a light sanding.
Also, because carbide is harder, the planer may require a bit more power to push through the cut. This is normal and not a sign of a problem.
Costs and Value
Infinity carbide-tipped knives for the Dewalt 734 typically cost around $60–$80 per set (two knives, four edges). In contrast, a set of OEM HSS knives costs about $30–$40. The higher upfront cost is offset by the longer life—if you plane a lot of abrasive material, carbide can save you money in the long run because you won’t need to buy replacements as often.
Some woodworkers also buy a second set so they can keep one sharp while the other is in the planer. That adds to the initial investment but reduces downtime.
Comparison: Infinity vs. OEM vs. Other Aftermarket
Compared to Dewalt’s stock HSS knives, Infinity carbide knives last much longer and are better for hardwoods and sheet goods. The main downside is cost and the slight risk of chipping on impact.
Other aftermarket brands like Freud, Amana, and Woodworker II also make carbide knives for the DW734. Infinity is often praised for its micro-grain carbide and precise grinding. Prices are similar across brands, so you can choose based on availability and reviews.
If you plan to use your planer only occasionally on clean softwood, HSS knives may be sufficient. But if you plane rough lumber, reclaimed wood, or plywood, carbide is a worthwhile upgrade.
Safety Tips
Always unplug the planer before changing knives. The cutter head is sharp—wear gloves or handle the knives carefully. Never try to adjust a knife while the planer is plugged in. Also, make sure the knives are firmly tightened before running the planer; a loose knife can fly out and cause serious injury.
When planing, always feed wood in the direction of the grain, and never plane pieces shorter than 12 inches unless you use a push block. Carbide knives are sharp, so they cut easily, but the same sharpness means the cutters can grab the wood if you feed it incorrectly.
Frequently Asked Questions
Will Infinity carbide knives fit my Dewalt 734 planer? Yes, Infinity Tools makes a specific set for the DW734 and DW733. They match the original dimensions and mounting holes.
How long do carbide-tipped knives last compared to HSS? Carbide can last 5–10 times longer than HSS, depending on the material. On clean softwood, you might get months of use; on plywood or MDF, the edge life is still much longer than HSS.
Can I sharpen carbide-tipped knives? Yes, but it requires a diamond wheel or a professional sharpening service. Many users simply flip the knife to the second edge and then replace it when both edges are dull.
Do I need to change the cutter head to use carbide knives? No, carbide knives are drop-in replacements for the existing cutter head. You do not need a helical head to use them.
Will carbide knives produce a better finish than HSS? They can, especially if the HSS knives are dull. A sharp carbide edge will give a clean cut, but the finish also depends on feed rate, depth of cut, and wood species.
Are there any downsides to carbide knives? The main downsides are the higher cost and the risk of chipping if you hit a nail. Also, carbide is harder, so it may dull slightly faster on extremely abrasive woods like teak, but it still outlasts HSS.
Related
- Childbirth Yoga Classes in Choa Chu Kang
- Childbirth Yoga Classes in Clementi: What to Know
- Isle of White Bed and Breakfast: Real Info
How pages are sourced and corrected: Sources and editorial policy.